A sample of soil has a volume of 0.5 ft^3 and a weight of 50lb. After being dried in an oven, it has a weight of 44lb. The specific gravity of soil is 2.70. Determine the degree of saturation of soil before it was placed in the oven.

A sample of soil has a volume of 0.5 ft^3 and a weight of 50lb. After being dried in an oven, it has a weight of 44lb. The specific gravity of soil is 2.70. Determine the degree of saturation of soil before it was placed in the oven.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Question 40 The given data shows a sieve analysis of a soil sample. Classify the soil using AASHTO…

Q: ) The given data shows a sieve analysis of a soil sample. Classify the soil using AASHTO Method.…

Q: 5. The results of field unit weight determination of a soil sample using the sand cone method is as…

A: Soil parameters of field is given which is used to calculate field density and dry density .…

Q: Determine the Mass of Solids, Ms. (Units of g, 2 decimal places)

A: The pycnometer method is used to determine the water content of a soil specimen and the specific…

Q: QUESTION ONE A particle size distribution curve is given in the figure below Classify the soil using…

Q: A 0.82 of 264

Q: Classify the soil using AASHTO Method.

A: AASHTO SOIL CLASSIFICATION:

Q: Question 2 J10p 180 grams of soil sample is in a cylindrical container, with a diameter of 40 mm and…

A: Given Data: mass of soil sample, w=180 g diameter of cylinder, D=40 mm height of cylinder, H=75 mm…

Q: In an experiment conducted by a soil engineer for the determination of the porosity and specific…

Q: he given data shows a sieve analysis of a soil sample. Classify the soil using AASHTO Method. Tables…

A: iLook at % passing through No 200 sieve =24%<35%so granular material A-1 or A-2

Q: What formula is suited to answer this question?

A: Given data in question Dry unit weight Water content 5 Samples are taken To find out Formula to be…

Q: ysis on a soil sample yields the following data. Plot the particle size distribution curve and…

A: Given:- Sieve No. and Sieve Size To find:- Plot the particle size distribution curve and classify…

Q: For a sample of soil, the following grain size characteristics are given: Sieve No. Percent Passing…

A: AASTHO classification system

Q: poratory apparatus for the following ests.Label and give the use/uses. 1. Determination of moisture…

A: Note- We are authorized to answer three subparts at a time since you have not mentioned which part…

Q: 1. Undisturbed soil sample was collected from the field in steel Shelby tubes for laboratory…

Q: Classify the soil using AASHTO Method.

A: AASHTO CLASSIFICATION:

Q: he given data shows a sieve analysis of a soil sample. Classify the soil using AASHTO Method. Tables…

A: iLook at the % passing through the sive 200=33<35% so granular soil

Q: You measure a soil sample's pH using a testing strip. If the reading is 5.2, how would you classify…

A: Soil mechanics : Soil mechanics is the study of the physical characteristics and usage of soils,…

Q: A soil sample has a volume of 120 in^3 and a total weight of 9.10 Ibs. After oven dried, the soil…

A: Given:- The volume of the soil sample = 120 in3 The total weight of the soil = 9.10 lbs After…

Q: The given data shows a sieve analysis of the soil sample. Classify the soil according to AASHTO…

Q: Classify the soil according to Unified soil classification. Explain each classification

A: Given Data: The sieve number and mass retained have been given in the problem. To Determine:…

Q: Question Answer Calculate the percentage of sand when the 40 second hydrometer reading is 35 g;…

Q: The given data shows a sieve analysis of a soil sample. Classify the soil using AASHTO Method.…

A: following table of data from sieve analysis is given:

Q: Usual types of significant Stone fragments, gravel, and sand Fine Silty or clayey gravel and sand…

A: To Determine Soil classification according to AASHTO soil classification system. Given Sieve number.…

Q: For determining the bulk density of a soil, a 188 g of soil sample was placed in a container of 552…

A: Weight of soil sample, W=188gInitial water content, w=24.55%Specific gravity of solids, Gs…

Q: A soil sample is required to have degree of saturation 60% at 18% water content. If specific gravity…

A: given- Degree of saturation S=60%water contentw=18%specific gravityG=2.6for cylindrical soil…

Q: HYDROMETER ANALYSIS ORIGINAL SAMPLE: WASHED SAMPLE: 112.75 118.75 115.65 MASS CONTAINER MASS…

A: according to MIT soil classification system, Gravel ranges from 60mm-2mm, sand ranges from…

Q: A sample of soil has a weight of 41.8lb, volume of 0.39ft^3, and a water content of 11.3%. What is…

Q: Classify the soil according to Unified soil classification Sieve No. 4 10 20 40 60 80 100 200 Pan…

A: Mass retained in each sieve is given. From that, we can find that how much percentage retained and…

Q: You’ve conducted a soil extraction on the site to have its soil profile determine, you’ve gathered…

A: Let's draw the phase diagram to proceed with the solution Let's say density of soil solid = dsolid…

Q: You've conducted a soil extraction on the site to have its soil profile determine, you've gathered…

A: Given data: Mass of soil sample=15 kgs Volume of soil sample=0.007 m3 Water content=15% Specific…

Q: 8. 200 grams of a soil sample has a grain size distribution as shown in the table below with a…

A: Given data in question Liquid limit 32% Plastic limit 15% Sieve analysis data To find out…

Q: 1. Classify the following soil: Soil A and E using the U.S. Department of Agriculture textural…

Q: A sample of clay soil of volume 1/1000 cubic meter and mass of 1.762 kg, after being dried out in an…

Q: A SOIL SAMPLE WAS TAKEN FROM A SITE AND WAS PLACED IN A CUBICAL CONTAINER WITH ONE SIDE EQUAL TO…

A: Given Data: Side of the cubical container is b=0.1 m. Net weight of soil is W=2 kN. Weight reduction…

Q: Pycnometer test has been carried out for the determination of specific gravity of soil solids and…

Q: A soil sample has a volume of 0.07 ft*3 and a total weight of 9.10 Ibs. After oven dried, the soil…

Q: U.S. sieve no. Percent passing 4 100 10 90 20 64

A: Given:- LL=23 PL=19 To find:- a) AASHTO soil classification system b) USCS

Q: Calculate Specific Gravity for the following soil sample. Test #1 Temperature 22 °C Mass of flask +…

A: The given data is: Temperature (T) = 22°C Mass of flask+ water (W2) = 670.4 Mass of flask+ water+…

Q: SKIPPED During test for water content determination on a sample pycnometer, following observation…

Concept explainers

Soil engineering for highway design

Soil engineering is a part of geotechnical engineering that deals with the characteristics of soil. It also helps to understand the behavior of the soil in different conditions. The basic concepts of soil are studied to check the strength, compressibility, and porosity of the soil. This makes soil engineering an important topic for civil engineering.

Question

Can I get a step by step for this question? A sample of soil has a volume of 0.5 ft^3 and a weight of 50lb. After being dried in an oven, it has a weight of 44lb. The specific gravity of soil is 2.70. Determine the degree of saturation of soil before it was placed in the oven.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Question 44 The given data shows a sieve analysis of a soil sample. Classify the soil using AASHTO Method. Tables are provided below. Sieve No. Diameter (mm) Percent Passing No 4 4.760 99 No. 8 2.380 91 No. 10 2.000 90 No. 20 0.840 85 No. 40 0.420 81 No. 60 0.250 79 No. 100 0.150 67 No. 200 0.075 60 Characteristics of No. 40 Fraction LL 39 PL 32 General classification Granular materials (35% or less of total sample passing No. 200) A-1 A-2 Group classification Sieve analysis (percent passing) No. 10 A-1-a A-1-b A-3 A-2-4 A-2-5 A-2-6 A-2-7 50 max. 30 max. 15 max. No. 40 50 max. 25 max. 51 min. 10 max. No. 200 35 max. 35 max. 35 max. 35 max. Characteristics of fraction passing No. 40 Liquid limit Plasticity index 40 max. 10 max. 41 min. 40 max. 11 min. 41 min. 11 min. 6 max. NP 10 max. Usual types of significant constituent Stone fragments, gravel, and sand Fine Silty or clayey gravel and sand sand materials ESC F4 FS F6 F7 FB F9 & 61 A4TECH Y P G J K 国因

1. The results of a standard Proctor test are given in Table Q1 below. Determine the maximum dry density of soil compaction and the optimum moisture content. Table Q1 Volume of Proctor Mass of wet soil in the mold Moisture content mold (cm³) (kg) 3.39 (%) 11.5 987 987 3.87 13.5 987 4.22 15.5 987 5.11 17.5 987 4.75 19.5 987 4.31 21.5
Following details regarding the particle size distribution and other index properties pertinent to the classification of soil. Choose three soils and classify each soil according to USCS and AASHTO classification systems. When necessary, assume Cu = 4.48 and Cc = 1.22.
- My courses > Soil-20-21 > Topic 3: Soil Compaction > Compaction Quiz The data in the table below was gotten from modified Proctor test for a soil sample having G,-2.62 w (%) 10 12 14 17 19 23 1.15 1.07 0.94 0.83 0.88 0.92 What is the degree of compaction if the field dry unit weight is 13.2 kN/m' and field moisture content is 9% ? O a. 71.3% Ob. 100% Oc. 94% Od. 80%
Determine the group symbol using the Unified Soil Classification System. Explain every step and criteria that you considered that lead to your final choice of classification.
Question 44 The given data shows a sieve analysis of a soil sample. Classify the soil using AASHTO Method. Tables are provided below. Sieve No. Diameter (mm) Percent Passing No. 4 No. 8 No. 10 No. 20 4.760 96 2.380 80 2.000 78 0.840 61 No. 40 0.420 56 No. 60 0.250 48 No. 100 0.150 39 No. 200 0.075 33 Characteristics of No. 40 Fraction LL 45 PL 36 General classification Granular materials (35% or less of total sample passing No. 200) A-I A-2 Group classification A-l-a A-1-5 A3 A-24 A-25 A-2-6 A-2-7 Sieve analysis (percent passing) No. 10 No. 40 No. 200 50 max. 30 max. 15 max. 50 max. 25 max. 51 min. 10 max. 35 max. 35 max. 35 max. 35 max. Characteristics of fraction passing No. 40 Liquid limit Plasticity index 40 max. 41 min. 40 max. 41 min. 6 max. NP 10 max. 10 max. 11 min. 11 min. Usual types of significant Stone fragments, gravel, and sand Fine Silty or clayey gravel and sand sand
How to solve the problem, may I request to put an explanation every step ?, Thank you so much.
The result of particle-size distribution of a soil sample is recorded below. Using the AASHTO classification table, determine the following: 1. Classification of soil A. 2. Classification of soil B. 3. Classification of soil C.
The following results were obtained by a mechanical sieve analysis. classify the soil using the Unified Soil Classification System. Sieve analysis % passing by weight is as follows: No.4 = 100% No. 40 = 89% No.200 = 65% Liquid Limit= 44 Plastic Limit = 23
Please Help! Once answered will Upvote!!
1. A soil sample was taken in site and brought back to the laboratory. It was found out that the weight of the soil is 2kg. The sample was placed to a container of 1L and 845 mL of water to fill the container. Calculate the Density and Unit Weight of the Soil Sample in English and in Metric Units.