A rotor of mass 10 kg is mounted midway on a 2 cm diameter horizontal shaft supported at the ends by two bearings. The bearing span is 80 cm. Because of certain manufacturing defect, the centre of gravity of the disc is 0.1 mm away from the geometric centre of the rotor. If the system rotates at 3000 r.p.m. Determine, the amplitude of the steady state vibration and the load transmitted by the bearing. Take E = 200GN / (m ^ 2

A rotor of mass 10 kg is mounted midway on a 2 cm diameter horizontal shaft supported at the ends by two bearings. The bearing span is 80 cm. Because of certain manufacturing defect, the centre of gravity of the disc is 0.1 mm away from the geometric centre of the rotor. If the system rotates at 3000 r.p.m. Determine, the amplitude of the steady state vibration and the load transmitted by the bearing. Take E = 200GN / (m ^ 2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

mass 1 is excited by a harmonic force whose maximum value and frequency are 2 N and 50 Hz, respectively. Where m1 = 5 kg, m2 = 5 kg, k1 = 2000 N/m and k2 = 2000 N/m. Which answer represents the amplitude X1 and X2?
Solve this question step by step.
A vibrometer with mass 0.86 kg and damping ratio ζ 0.62 is designed to measure vibration in the frequency range ωb = 34.8-84.7 rad/sec. Chose the appropriate stiffness from the given values to guarantee the maximum error will not exceed 2% Note:ZY=r2(1−r2)2+(2rζ)2√ a. 115 N/m b. 367 N/m c. 85 N/m d. 2173 N/m e. 680 N/m
[6] An instrument panel weighing 30 lb is installed in a vehicle on a flexible mount that has an equivalent stiffness k = 400 lb/in and negligible damping. As a result of engine vibration, the vehicle vibrates with a steady-state amplitude of o.25 in at a frequency of 40 Hz. Determine the steady-state amplitude of vibration of the instrument panel.
Answer ASAP would be appreciated
A free vibration of the mechanical system shown in Figure 3 indicates that the to after four consecutive 3. amplitude of vibration decreased to 1/3 of the xo value at t = cycles of motion (i.e. x4 at t = t4). Determine the corresponding spring constant k if m = 15 kg and the viscous friction coefficient b = 4 N-s/m in the system. m Figure 3
A motor rotates at 750 rev/min and has a moment of inertia of 0.15 kgm2. It drives a load through a gearbox at 250 rev/min with a moment of inertia of 0.25 kgm2. The torque on the load shaft varies sinusoidally with an amplitude of 180 Nm. The speed of the load is to be regulated to ± 4% of the mean by adding a flywheel to the motor shaft. Calculate this moment of inertia to be added and the mass of the flywheel that is a plain disc of radius of 400 mm.
The spring constant of the spring-mass-damper system is k = 5 kN/m, the damping constantcritical value ckr = 200 Ns/m and logarithmic decrement δ = 2. System initial conditionsare x0 = 0 m and v0 = 1 m/s. Determine the damping due to the initial conditionsthe maximum value xmax of the displacement of the characteristic vibration and its moment of occurrence tmax. Specifyresponse, i.e. in this case the values of the variables needed by the station x(t).
A bench of mass m = 1 kg and moment of inertia J0 = 0.3 kg.m2 is supported by rigid springs k1 = 3000 N/m and k2 = 2000 N/m. If the supports are located at l1 = 0.5 m and l2 = 0.8 m, find the frequencies natural and vibration modes of the system.
2. The machine shown below, with the rotating unbalance, operates a speeds between 18 and 60 rad/sec. Determine the minimum value of damping coefficient c needed to keep the amplitude of vibration below .3 inches. M = .026 lb sec2/in m = .0026 lb sec2/in r = 2 in. K = 3.75 lb / in Rotating Unbalance ww K X₁ M C Ty
Three (very small) beads with masses m, m, and μ can slide without friction on a (very thin) fixed ring of radius a and are connected to each other by (weightless) springs of equal stiffness k and equilibrium length = √√3a. Find the normal frequencies and normal modes of vibration for this system. Interpret the physical meaning of the modes you have found. m .k,l www wwww m mu wwwww.. k,l
The spring-mass-damper system shown below has m1 = m2 = 3.4 kg and k = 97.7 N/m. In addition, a damping factor of 0.3 is given. The initial position and velocity of the system is x(t=0)=4.3 mm and x'(t=0)=0 m/s respectively. Frictionless pulley m2 Calculate the time required for the amplitude to reduce to 10% of the initial conditions.