roller slides in a slot by the amount δP = 0.25 mm in the direction of the force F. Both bars have an area of cross-section of A = 100 mm2 and a Modulus of Elasticity E = 200 GPa. Bar AP and BP have lengths of LAP= 200 mm and LBP= 250 mm respectively. Determine the applied for

Q: Cable AB supports the uniformly distributed load of 4 kN/m. If the slope of the cable at A is zero,…

A: Option (b): Tmax = 300 kN , S = 75 m

Q: BLOCK C CABLE FRICTION p = 0.35 for all surfaces In the beam system shown in the figure, Block A and…

A:

Q: In the lattice system shown in the figure, select the distance a to be between 2 meters and 5 meters…

A: Let us assume the length "a" = 2 m And the force "P" = 20kN From the figure the angle between…

Q: The rigid bars ABC and CD are supported by pins at A and D and by a steel rod at B. There is a…

A:

Q: A distributed force and a concentrated force act on the 20m long bar shown below. 2 kN 400 N/m A B *…

A:

Q: A rigid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P…

A:

Q: Since the suspended mass is m=1500 kg as shown below; Find the force (F) N and the stress N/mm2 in…

A:

Q: The system shown is subjected to three axial forces P₁ = 250 kN, P₂ = 400 KN and P3 = 275 kN. What…

A: To find: The total change in length due to loading. Given: The length of bar AB is  lAB=1 m. The…

Q: As shown, an L-shaped bar is supported by a pin at joint A. The bar's dimensions are aaa = 620 mmmm…

A: Introduction We shall compute the real orientation of the applied force at an angle in this…

Q: area of the rod is 1200 mm a=11.7u m/(m.'C) and E=200 GPa. Solve assuming (a) that the wall is rigid…

A:

Q: Consider the force P applied at point A on the plate of the figure shown (image 1). Assuming that…

A:

Q: The frame shown is fitted with three 36 cm diameter frictionless pulleys. A force of F = 920 N is…

A:

Q: one end of the uniform beam of mass 50 kg is hinged to a wall. The other end of the beam is…

A:

Q: The exercise machine consists of a rigid bar, pin connected to the frame at A. As the man pushes up…

A: Given data  Stiffness = 500lb/ft.  Find the force applied vertically upward

Q: 10 10¹ D C 8 Fig.4 40° 8' B 5000 lb

A: Given : The free body diagram is,

Q: В G 5 m

A: For solution refer below images.

Q: One end of a uniform { = 3.80-m-long rod of weight w is supported by a cable at an angle of e = 37°…

A: TO FIND; The minimum distance x from point A so that rod does not slips.

Q: The uniform 44 kN bar BC is supported by a pin at C and the aluminum wire AB. The cross-sectional…

A: GivenW=44kNA=178.5mm2E=71GPa

Q: Determine the force in the cable OC and the elongation of the spring OA, OB necessary to support a…

A: The mass hang on the cable is given as, m=400 kg The length of the cable are given as, a=4 m b=5 m…

Q: The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by…

A: Given that The force P→ is 19i^-10j^ KNThe coordinates from the figure are:A 2,0,-3; B (0,6,0); C…

Q: A₁ = 6000 mm² 1 6m 2 Figure 1 2 A₂ = 5000 mm² 3 P = 2000 KN 40° 3 A3 = 5000 mm² 3m 4m Calculation…

A: The elastic modulus is

Q: PROBLEM 4: Find the reaction force components at point A and B. The member AB has a length of L=10m.…

A:

Q: A heavy spool rests on the ground at point A and against the wall at point B. Find force F required…

A: Given that, Mass of the spool, m=100 kg,Radius of spool, ri=200 mm, and ro=460 mm,Coefficient of…

Q: Rope BCA passes through a pulley at point C and supports a crate at point A. Rope segment CD…

A:

Q: The system of two springs shown below is loaded by a force F = 200 N and the result is a deformation…

A: Given data  F = 200 N  s = 3mm  C1 = 2.5C2 To determine  Overall stiffness of the system

Q: The linkage shown is used in a vehicle suspension system. Find the forces indicated below when a…

A: Solution: Given Data: F = 820 lb θ=22o   Note: Dear Student! As per our guidelines, we are only…

Q: Rope BCA passes through a pulley at point C and supports a crate at point A. Rope segment CD…

A: Given: Tmax=165 lb φ= 64o

Q: the bent bar AB weighing 10lb/ft is mounted as shown in figure 2 upon a carriage weighing 250 lb.…

A: Solution: Given Data: w=10 lb/ftW=250 lbP=108 lb

Q: y P2 B P1

A: Drawing the free body diagram of the given truss as shown below – At A the support is fixed and at…

Q: A straight bar 450 mm long is 10 mm in diameter for the first 200 mm length and 20 mm in diameter…

A: Given data: L=450 mmd1=10 mmL1=200 mmd2=20 mmF=10 kNE=2×105 N/mm2 Need to determine the decrease in…

Q: The circular shaft of constant cross - section carries three pulleys and belts which are vertical .…

A:

Q: Find the reaction forces at pin A and smooth rocker at B. Assume F = 15 kN. Ax = Ay= B = y F A 30° 6…

A: The reaction forces are shown in the figure below.

Q: 3. If only one person is on the swing in the image below, it is comparable to a point load of F =…

A: Solution

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.