A rod of length 40 mm is stretched to make a rod of length 60 mm. It is compressed to make a rod of final length 30 mm. Consider the longitudenal tensile strain as positive and compressive strain as negative.

A rod of length 40 mm is stretched to make a rod of length 60 mm. It is compressed to make a rod of final length 30 mm. Consider the longitudenal tensile strain as positive and compressive strain as negative.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

# 2-12. Normal Strain in rods constrained by walls with misfit Rods (1) and (2) were supposed to fit exactly between the rigid walls at A and C, as indicated in the figure below. However, rod (2) was manufactured a small amount, 8L, too long. A technician decides to lower the temperature of rod (2) by AT so that he can insert it in the space between B and C. When rod (2) returns to its initial temperature, the length of each rod is no longer the same as the original one, and the resulting strain is often called "residual strain"". Rod (1) has Young modulus E₁ = 74 GPa and cross-sectional area A = 1749 mm². Rod (2) has Young modulus E₂ = 204 GPa and same cross-sectional area A. Both rods have length L = 738 mm. L L (1) € = E₁,α₁, A B Ez az. A (2) Determine the resulting "residual" normal strain e in rod (1) when 8M = 9.10-¹ mm. -10-3 mm/mm
Find the Modulus of elasticity if stress is 45 MPa and strain is 0.03
Q 2: A circular rod of 15 mm diameter and 120 mm length, is subjected to 2.5 RN tensile load if the diameter become 12 mm find 1. True stress. 2. The length of the rod after deformation.
Let's consider a rod having a solid circular cross-section with diameter of 5 mm and it is made of a material having a Young's modulusE=120 Gpa and a Poisson's ratio of 0.33. If a tensile force F is subjected to that rod cross-section, the diameter becomes 4.995 mm. determine the applied force F.
Can you please answer question B, thank you
Find the initial length of rod if strain value is 0.0003 and change in length value 0.3 mm
PROBLEM SOLVING: A rigid bar is supported by three non-rigid steel rods, as shown. Rods AB and FG are 0.8 m long with a cross-sectional diameter of 30 mm. Rod CDE is made up of equally-long 0.40 – m CD and DE whose cross-sectional diameters are 60 mm and 30 mm, respectively. A 45 kN downward load is applied to the rigid bar. There is no initial strain before the application of the load. Let Esteel = 200 GPa Determine the internal forces on rods AB, CDE, and FG Determine the displacement of the rigid bar. If the allowable displacement of the horizontal rigid bar is 0.071 mm downwards, what maximum allowable vertical load can be applied for a factor of safety of 3? А F 0.40 m 60mm¢ D 0.8 m 0.8 m 30mm¢ 30mmф 0.40 m 30mm E G 45 kN
8. A steel 0.6 inch x 1.2 inch steel 90 m long is subjected to a 4500 lbs tensile load along its length. poison's ratio is 0.3. Find A. The deformation along its length B. The deformation along its thickness C. The deformation along its width D. The lateral strains
a) Calculate the principal strains, given that the state of plane strain for an element is: E = 25microns E, = 100microns Yy =-45microns b) An axial load of 3 kN is applied to the solid tubular member as shown in Figure 1. The length of the tube is 2.5 metres, the radius is 15 mm. The modulus of elasticity is 200 GPa. Calculate the elongation due to the loading, giving the answer in microns. Length of tube: 2.5m 8 Load: 3 kN Radius of tube: 15mm Figure 1
The structure shown in Fig. la is subjected to loading P and T. A set of strain rosette is positioned at point A for strain measurement. The orientation of the strain rosette is shown in Fig. 1b. The material properties are given as E = 200 GPa, G = 77 GPa and v = 0.3. If P = 10 kN and T= 250 Nm, find the following: i. The state of stress at point A and sketch the stress element. ii. The principal stress at point A and sketch the stress element. iii. The principal strain at point A and sketch the strain element. iv. The values of each strain gauge (Ea, Eb and ɛc). V. Name one change that can be done to lower the strain value at point A. 50mm 75mm 120 120° T Ø 50mm Ø35mm Fig. la Fig. 1b -----
Sketch two more stress-strain diagrams, again one for a ductile material and one for a brittle material. Draw the stress-strain diagrams so that the modulus of toughness for the brittle material is greater than the modulus of toughness for the ductile material.
Figure 2.1. shows two long plates with same material and equal width w=20 mm that are subjected to a uniaxial tensile load o. One of the plates has a single small central hole with diameter 4mm and another plate has two small holes with a distance of 8mm from each other. The holes are perpendicular to the external tensile load. Develop a computer code (or simulation model) and analyze how stresses will be distributed at the tip of the holes in these two plates for different values of 0. 4mm Figure 2.1. 8mm 4mm