A rising gradient AB and a falling gradient BC are to be connected by a vertical curve.Based on the data given in Table Q1, design the curve at 20 metres intervals.Q1.Table Q1 (Units are in metres)First Grade (+ %)Distance of highest/lowest ptRL of highest/lowest pt3.6Second Grade (+ %)38.572-1.7Length of Curve (L)Sighting Distance (SSD)Driver's eye (h,)Object height (h,)Chainage AChainage BChainage of highest/lowest pt3788.4151501.050.3Reduced Level BANSWERS (Q1)DataFirst Grade (+ %)Second Grade (+ %)Sighting Distance (SSD)Driver's eye (h,)Object height (h )Chainage highest/lowest ptRL highest/lowest pointSolutionLength of CurveChainage AChainage BChainage CDist. high/low ptOffset high/low pt (y)RL Grade high/low ptdH high/low ptRL ARL BRL CRL onRL onChainagedHygradecurvePlease add additione

Introduction : The rate of change of a multivariable function as one advances away from an in a…

A rising gradient AB and a falling gradient BC are to be connected by a vertical curve. Based on the data given in Table Q1, design the curve at 20 metres intervals. Q1. Table Q1 (Units are in metres) First Grade (+ %) Second Grade (+ %) Length of Curve (L) Sighting Distance (SSD) Driver's eye (h,) Object height (h,) Chainage A Chainage B Reduced Level B[ Distance of highest/lowest pt| RL of highest/lowest pt Chainage of highest/lowest pt| 3.6 38.572 3788.415 -1.7 150 1.05 0.3 ANSWERS (Q1)

A rising gradient AB and a falling gradient BC are to be connected by a vertical curve. Based on the data given in Table Q1, design the curve at 20 metres intervals. Q1. Table Q1 (Units are in metres) First Grade (+ %) Second Grade (+ %) Length of Curve (L) Sighting Distance (SSD) Driver's eye (h,) Object height (h,) Chainage A Chainage B Reduced Level B[ Distance of highest/lowest pt| RL of highest/lowest pt Chainage of highest/lowest pt| 3.6 38.572 3788.415 -1.7 150 1.05 0.3 ANSWERS (Q1)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Make your own 1 problem for the simple and compound curve with a solution on how you answer. Write it on a clean paper with your problem and complete solution. Then box your final answer. for simple curve determine: the radius, the external distance, the middle ordinate, and the tangent distance. for the compound curve determine: the radius of the 1st curve, the radius of the 2nd curve, the Length of the 1st curve, the Length of the 2nd curve, the Long chord , the Long chord 2, Sta. PCC Stat. PT
COMPLETE AND COMPREHENSIVE SOLUTION ANF FINAL ANSWER IN 2 DECIMAL PLACES. Determine the radius of a simple curve that will connect the given tangents and pass though point P, which is located from PI by distance and angle measurements as shown in the Figure:
The instrument used was a transit with an internal focusing telescope and a stadia interval factor of 99, compute for the gradient from A to B if all the stations are in a straight line.
For a highway curve with Da = 5°00', I = 20°30', and Pl station = 63 +25.53 ft, calculate the requested values to lay out the circular curve at full stations (100 ft). M 18.29 ft Submit Part E Correct Correct answer is shown. Your answer 18.28 ft was either rounded differently or used a different number of significant figures than required for this part. Previous Answers Calculate the external distance. Express your answer to two decimal places and include appropriate units. E = 18.58 ft Submit Part F Previous Answers ✓ Correct Correct answer is shown. Your answer 18.585 ft was either rounded differently or used a different number of significant figures than required for this part. Tabulate stations, deflection angles, and incremental chords to lay out the curve at full stations (100 ft). Express angles in degrees to four decimal places; express first station numbers as integers; second station numbers and chord lengths should be expressed in feet to two decimal places. The PC station…
Q9: Calculate the right of way of rural divided four-lane highway has depressed median and it is constructed on embankment. The median width is 4.0 m, embankment height is 6m, lane width is 3.5 m, shoulder width is 2.60 m and side slope is 1:3 (V:H).
Under nonuniform and slippery road conditions, the four forces shown are exerted on the four drive wheels of the all-wheel-drive vehicle. Determine the resultant of this system and the x- and y-intercepts of its line of action. Note that the front and rear tracks are equal (i.e., AB-CD. 6. 300 N B 30 760 mm 150 N 760 mm 30% 300N A D. 200 N 1520 mm 1120 mm
Given a design radius for the circular curve of 620m, a deflection angle of 95 degrees and a transition curve length of 85.5m, calculate the length of the circular curve. Note: Your answer should be provided to ONE decimal place.
You are a civil engineer who has been given the assignment to redesign the curved roadway in Example 6.3 in such a way that a car will not have to rely on friction to round the curve without skidding. In other words, a car moving at the designated speed can negotiate the curve even when the road is covered with ice. Such a road is usually banked, which means that the roadway is tilted toward the inside of the curve. Suppose the designated speed for the road is to be 13.4 m/s (30.0 mi/h) and the radiusof the curve is 35.0 m. You need to determine the angle at which the roadway on the curve should be banked.
The length of curve of a simple curve having a degree of curve 40 is equal to 210 m. Compute for the middle ordinate and external distance
A student releases a system on an incline as shown. The coefficient of friction of static friction between the 20kg box and the surface is 0.28 and the coefficient of kinetic friction is 0.16. Neglect drag. What is the magnitude of maximum static friction between the block and the surface in this situation? 47.1 What direction is the friction on the 20kg block? up-left What direction will the 20kg block slide? 20kg 7.6kg neither What is the magnitude of the friction? 26.5 What is the magnitude of the net force on the system? 0. What is the magnitude of the system's acceleration? 0.015 m/s? What is the tension in the string? 74.6 cannot be de check answers nallenge ne Calculator und = 343m/s ant figures