A rigid vessel contains fluid at 1 MPa and 260 degree with a volume of 0.14 m³ is cooled until the fluid pressure becomes 0.4 MPa. Determine the final temperature and heat transfer amount if Fluid is air

A rigid vessel contains fluid at 1 MPa and 260 degree with a volume of 0.14 m³ is cooled until the fluid pressure becomes 0.4 MPa. Determine the final temperature and heat transfer amount if Fluid is air

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.28P

See similar textbooks

Similar questions

Water at 50°C and 1 atm pressure is heated to 100°C at constant pressure. Using coefficient of volume expansion data, determine the change in the density of water. (Just write the numerical answer. Include - if the answer is negative. No need to put the unit.) Properties of saturated water Volume Specific Thermal Prandti Enthalpy Expansion Number Density P. kgima Conductivity k, Wim - K Dynamic Viscosity H. kgfm -s Heat Saturation of Coefficient G Jkg - K Pr 8, 1/K Liquid Pressure Temp. T. "C Vaporization hng, kkg Pat, kPa Liquid Vapor Liquid Vapor Liquid Vapor Liquid Vapor Liquid Vapor 1854 1857 1862 0.561 0.571 0.580 1.792 x 10-3 1.519 x 10-3 0.0176 1.307 x 10-3 1.138 x 10-3 0.0182 1.002 x 10-3 0.973 x 10-5 1.00 -0.068 x 10-3 0.015 x 10 0.733 x 10- 0.138 x 10 3 0.195 x 10 3 4217 0.0171 0.922 x 10 5 0.934 x 10-5 0.946 x 10 0.959 x 10 0.01 0.6113 999.8 999.9 0.8721 1.2276 999.7 0.0048 2501 2490 13.5 0.0068 4205 0.0173 11.2 1.00 10 0.0094 2478 4194 9.45 1.00 0.0128 0.0173 2466 2454 8.09…
350 pipes are fixed as square in a pipe bundle used for condenser. PipeThe outer diameters are 8 mm and the steam at 0.2 bar is desired to be condensed on the pipes. pipe outer The surface temperature is kept constant at 30 °C. If the length of the pipes is 1.5 m, the heat transferred in the systemCalculate the amount of energy and the amount of condensed steam
If the pressure of a substance is increased during a boiling process, will the temperature also incre ase or will it remain constant? Why?
Compartnments A and B of the tern k Shown in the figure below are closed and filled with air end a liquid with el specific grauity equal to o.6. 3.5hpa(gauge) B Open to the et moshore 3.ocm air Liquid with e specific grauity =0.6 water mercary w th a specific grauity =13.6 O If the atumospheric press ure is lol kpa Cabr) and preffure gaugle reads 3.5trpa (gauge).determine the manometer reading, h.
Bartleby has a solution for the following problem: As shown in the diagram, the state of helium gas is changed in such a way that its PVgraph is a straight linesegmentwith volume V0increases to yV0and pressure P0increases to xP0where xand yare arbitrary constants. During this process the total heat transferred to the gasis equal to the heat necessary to double the absolute temperature of the gas at constant volume. What is the maximumratioforthe volume increase? I do not understand why you can say that the first law of thermodynamics gives that the sum of work equals the sum of heat when the process is not isothermal. Therefore, setting work equal to heat in step 2 does not make sense to me. Could you please elaborate why this is valid? Additionally, why do we know that this is the maximum y? Doesn't the max y occur for an isobaric process? Thank you.
NEED CORRECTLY IN PROPER HANDWRITING. URGENT. SURELY UPVOTE. . THANK YOU
A water tank is completely filled with liquid water at 40°C. The tank material is such that it can withstand tension caused by a volume expansion of 5 percent. Determine the maximum temperature rise allowed without jeopardizing safety. Assume a volume expansion coefficient value at that of 65 °C. (Just write the numerical answer. Include - if the answer is negative. No need to put the unit.) Properties of saturated water Volume Specific Нeat Thermal Prandti Enthalpy Density P. kg/m Expansion Coefficient B, 1/K Liquid Conductivity k, W/m - K Dynamic Viscosity Number Saturation of G, J/kg K H. kg/m - s Pr Temp. T. °C Pressure Vaporization Pat, kPa Liquid Vapor hig, kJ/kg Liquid Vapor Liquid Vapor Liquid Vapor Liquid Vapor 2501 2490 2478 0.561 0.571 0.580 1.792 x 10-3 1.519 x 10-3 1.307 x 10-3 1.138 x 10-3 1.002 x 10-3 0.922 x 10-5 0.934 x 10-5 0.946 x 10-5 0.959 x 10-5 0.973 x 10-5 0.6113 1854 0.0171 0.0173 999.8 0.0048 -0.068 x 10 3 4217 4205 13.5 11.2 0.01 1.00 0.0068 0.0094 0.0128…
I need the answer as soon as possible
Determine the capillary rise of kerosene at 68°F IN INCHES in a glass tube having a diameter of 0.25 inches From given: Density of kerosene at 68°F =1.57 slugs/ft^3 Surface tension of kerosene at 68°F =0.0017 lb/ft
What is the phase and pressure of water at 280°C with specific volume 0.92 m3/kg? answer : superheated vapour, 0.2866 MPa Explain how it came
One kg of steam is contained in an elastic baloon of spherical shape which supports an internal pressure proportional to its diameter. The initial condition of steam is saturated vapour at 110oC heat is transferred to steam until pressure reaches 200kPa. Determine:Final temperature and Heat transferred. Take Cps = 2.25 kJ/kg.K
Detrermine (a) The state of water at each state of the process(b) The amount of heat that is rejected to the environment in Btu(c) At which part of the process is useful work involved? Calculate the workin Btu? Is this work useful or spent on the system? What is the magnitudeof change in internal energy of the system at this part of the process?(d)Show the process in a p-V diagram