A rigid chamber contains 100 kg of water at 500 kPa, 100°C. A paddle wheel stirs the water at 1025 rpm with a torque of 145 N-m while an internal electrical resistance heater heats the water, consuming 8.5 amps of current at 110 Volts. Because of thin insulation, the chamber loses heat to the surroundings at 27°C at a rate of 1.10 kW . Determine the rate at which the stored energy of the system changes. Express your answer to five significant figures. VO AE It vec ? dE dt kW

A rigid chamber contains 100 kg of water at 500 kPa, 100°C. A paddle wheel stirs the water at 1025 rpm with a torque of 145 N-m while an internal electrical resistance heater heats the water, consuming 8.5 amps of current at 110 Volts. Because of thin insulation, the chamber loses heat to the surroundings at 27°C at a rate of 1.10 kW . Determine the rate at which the stored energy of the system changes. Express your answer to five significant figures. VO AE It vec ? dE dt kW

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Define the work (boundary) done on an adiabatic system is equal to the increase in the energy of the system.
a) A gas is trapped in a piston-cylinder device. The initial pressure and temperature of the gas are 500 kPa and 300 K, respectively. The system undergoes an isothermal expansion process, in which 15KJ of boundary work is done by the gas and 3KJ of paddle-wheel work is done on the gas. Determine the amount heat transfer during this process. Explain the direction of the heat transfer.
Determine the work required (in kJ/kg) for a pump that is used to increase the pressure of a liquid water stream from 100 kPa to 1500 kPa isothermally at 20 °C. The specific heat of water (C) is 0.0035 kJ/kg.K. its specific volume is 0.001031 m³/kg and its volume expansivity (B) is 250x10 K
A frictionless piston-cylinder device contains a gas initially at 0.8 MPa and 0.015 m³. It expands quasi-statically at constant temperature to a final volume of 0.030 m³. What is the work output during this process?
A 25 kW automobile engine consumes 1.25 kg of gasoline when it runs for 10 minutes. What is the efficiency of the engine since the lower calorific value of gasoline is 43000 kJ / kg?
The “Energy Guide” label of a refrigerator states that the refrigerator will consume $170 worth of electricity per year under normal use if the cost of electricity is $0.125/kWh. If the electricity consumed by the lightbulb is negligible and the refrigerator consumes 400 W when running, determine the fraction of the time the refrigerator will run.
A gas contained in a vertical cylindrical tank has a volume of 11.12 m3. The gas receives a paddle work of 7.5W for 1hour. If the density of the gas at the initial state is 1.5 kg/m3, determine the specific heat gain or loss if the specific internal energy of the gas increases by 16.2kJ/kg.
Imagine a car traveling at a constant speed along a road. Determine the temperature and work interactions and direction by taking the following as a system: (a) automobile radiator, (b) automobile engine, (c) automobile tires, (d) road, (e) air surrounding the car.
None
Heat transfer
A variable-load piston-cylinder device contains air (cp = 1.005 kJ/kgK; cv = 0.718 kJ/kgK) at 500 kPa and T=12 oC. A paddle wheelequipped within the system and turned by an external electric motor until 65 kJ/kg of work has been transferred to the air. During this process the gas volume is quadrupled while maintaining the temperature constant by transferring heat to the gas. Determine (a) the final pressure, (b) the amount of required heattransfer (c) Show this process on a P-v diagram. Do not use Table A-17 while solving this problem. YOUR ANSWER SHEET SHOULD INCLUDE THE SOLUTION AND THE TABLE BELOW (a) Pinal [kPa] = (b) q [kJ/kg]