A rigid bar of negligible weight is supported as shown in the figure. If W = 80 KN, compute the temperature change that will cause the stress in the steel rod to be 55 MPa. Assume the coefficients of linear expansion are 11.7 µm/(m.°C) for steel and 18.9 µm/ (m. C) for bronze.

A rigid bar of negligible weight is supported as shown in the figure. If W = 80 KN, compute the temperature change that will cause the stress in the steel rod to be 55 MPa. Assume the coefficients of linear expansion are 11.7 µm/(m.°C) for steel and 18.9 µm/ (m. C) for bronze.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. A rigid bar of negligible weight is supported as shown. If W = 80 kN, compute the temperature change that will cause the stress in the steel rod to be 55 MPa. Assume the coefficients of linear expansion are 11.7 µm/(m. °C) for steel and 18.9 um/ (m.°C) for bronze. DIN Steel L = 1.5 m A = 320 mm² 1m E= 200 GPa 2.5 m Bronze L = 3m A = 1300 mm² E = 83 GPa W 1.5 m
2. A rod is composed of an aluminum section rigidly attached between steel and bronze sections as shown in the figure. Axial loads are applied at the positions indicated. The cross-sectional area of the rod is 300sq.mm. Express your answer in MPa. Determine the stress in the steel. b. a. Determine the stress in the aluminum. Determine the stress in the bronze. C. STEEL ALUMINUM BRONZE 56kN 14kN -0.6m- -0.9m- -0.76m-
SHOW COMPLETE SOLUTION AND DRAW ILLUSTRATION
3. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 13.05 ksi, or in bronze of 100 MРа. Aluminum A = 400 mm Bronze A = 200 mm Steel A = 500 mm? 2P 4P 2.5 m 2.0 m 1.5 m
An aluminum tube with the hexagonal cross-section shown is 2.5 ft long and has a constant wall thickness of 0.080 in. Find (a) the largest torque that the tube can carry if the shear stress is limited to 7200 psi. Use G = 4 x 106 psí for aluminum. 11.5 in 0.075 in O 6734 lb-in O 7634 lb-in O 6374 lb-in O 7346 lb-in
a)Calculate the stress in the copper bar (in MPa).b)Calculate the axial deformation in the brass bar (in mm).c)Calculate the axial deformation in the brass bar (in mm).
3) An bronze rod is rigidly attached between a aluminum rod and a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximum allowable value of P that will not exceed a stress in steel of 140MPA, in aluminum of 90MPA or in bronze of 100MPа. Aluminum A = 500mm? Bronze A = 200mm? Steel A = 150mm2 2P ЗР L st = 1.2m L br = 2m Lal = 3.5m
A mild steel flat of width 100 mm and thickness 12 mm is bent into an arc of a circle of radius 10 m by applying a pure moment M. If Young's modulus tilde E = 200GPa then the magnitude of M is? (a) 72 Nm (c) 216 Nm (b) 144 Nm (d) 288 Nm
Three aluminum rods support the rigid L-shaped bracket BCF as shown in the figure. Determine the stress in rod DE (express answer in MPa) if rod FG is cooled by 50°C. All three rods have the same cross-sectional area of 1000 mm^2. Use 73.1 GPa and 23 x 10^-6 /°C for the modulus of elasticity and the coefficient of thermal expansion of aluminum, respectively.
DEFORMATION DUE TO AXIAL FORCES PROBLEM 1: CE Brd Exam The rigid block shown weighs 176.4 kN. It is held in position shown with stress in the supporting rods shown initially zero. If the former is to remain horizontal when released, 1a. Find the ratio of forces in bronze and steel a. 0.389 c. 0.397 1b. Find the stress in the bronze rod. b. 0.344 d. 0.416 а. 31.92 MPа с. 28.73 МPа 1c. Find the the elongation of steel rod. b. 53.34 MPa d. 39.67 MPa a. 0.615 mm b. 1.83 mm c. 2.31 mm d. 2.12 mm 0.6 m BRONZE A=900mm STEEL STEEL A=600mm A=600mm 1 m E-200GPA E-83GPA E=200GPA W = 176.4 kN
A 260 mm bar AB with a rectangular cross section of 17 x 30 mm, consists of two aluminium layers with cach being 6 mm thick and brazed to a centre steel layer of 5 mm thickness as shown in Figure Q3. An axial tensile force of P- 37 kN is applied to the assembly by means of a rigid end cap at B. Given that the assembly is fixed at end A and the Young's modulus of aluminium and steel are E.= 70 GPa, Es= 200 GPa, respectively, determine: i Whether this structural configuration is statically determinate or statically indeterminate, and clearly explain your reasoning. ii. The normal forces in the aluminium layers and the steel layer i. The normal stress in the aluminium layers and the steel layer. State whether the stresses are in tension or compression iv. Determine the deformation of the assembly Cross section of the bar 6 mm 5 mm 6 mm 30 mm 260 mun Aluminium. Steel- Aluminitum Nא 37 30 mm
A vibration isolation support consists of a rod A of radius R₁ and a tube B of inner radius R₂ bonded to an 80-mm-long hollow rubber cylinder with a modulus of rigidity G = 10.93 MPa. Determine the required value of the ratio R2/R1 if a force P = 13 kN is to cause a 2-mm deformation of rod A. B R₁ R₂ .. 80 mm The required value of the ratio R2/R₁ is 1.422