A retaining wall is shown in the Figure below. For each problem, determine the Rankine active force, Pa, perunit length of the wall and the location of the resultant.H12 mH₁4mSurchargeFrictionless wallSand71di=0Y₁Y₂17 kN/m² 23.2 kN/m²↓Groundwater tablei(deg) : (deg)3642425 kN/m²SandEy (saturated unit weight) DE MOITAMINE72-0

Answered: Image /qna-images/answer/32629e17-d4e2-4213-a35d-50ce583ca2fb.jpg

A retaining wall is shown in the Figure below. For each problem, determine the Rankine active force, Pa, per unit length of the wall and the location of the resultant. H 12 m H₁ H₁ 4 m Surcharge q Sand 71 c=0 Frictionless wall Y₁ 17 kN/m² 23.2 kN/m² Groundwater table Sand 472 (saturated unit weight) -0 Y₂ (deg) (deg) 36 42 4 25 kN/m² D12EIC ИОГРАФИИОН

A retaining wall is shown in the Figure below. For each problem, determine the Rankine active force, Pa, per unit length of the wall and the location of the resultant. H 12 m H₁ H₁ 4 m Surcharge q Sand 71 c=0 Frictionless wall Y₁ 17 kN/m² 23.2 kN/m² Groundwater table Sand 472 (saturated unit weight) -0 Y₂ (deg) (deg) 36 42 4 25 kN/m² D12EIC ИОГРАФИИОН

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

geotechnical, civil engineering, please solve question 8
Q4-A:For the soil profile shown below, the coefficient of volume compressibility varies linearly from 420x106 m²/kN at 100 kN/m² to 320x106 m²/kN at 200 kN/m². calculate the final building settlement. Answer B or C building weight=90x10³ Q4-B:Mention the graphical procedures used for determining the maximum past pressure. - 0.0 Area=18x18m y=20kN/m² H - -1 y=20kN/m² Q4-C: A soft clay layer 0.5m thick is sandwiched between layers of sand. The initial vertical total stress at the center of the clay layer is 50 kPa and the porewater pressure is 20 kPa. The increase in vertical stress at the center of the clay layer from a building foundation is 25 kPa. What are the vertical effective stress and porewater pressure at the center of the clay layer when 60% consolidation occurs? y-20kN/m² y=19.2kN/m² excess pervious layer sand sand sand clay -3- -3.5 71,5 --5- 95 -9 T₂
33
17
سويل In the figure below if h,=3 m: h2=2.8 m; q=500 kN/m? 9- KN/m? (net stress increase) AVAVAV Sand y= 15.7 kN/m 1.5 m Groundwater Table BxL= 1.5 m x 3.0 m him Sand Yat= 16.5 kN/m Clay Yaa= 16 kN/m e, = 0.68 C. = 0.25 C, = 0.06 h2 Please fill in the blank with only one digit and no units like this 123.4 A) if the drainage in the clay layer is single drainage, resulted in 90% primary consolidation in 120 days. Find the coefficient of consolidation in cm/day. 554.0 B) If c, =621 cm/day, and the tool settlement is 30 cm, How long (in days) will it take for the clay layer in the field to reach 11 cm consolidation? 13.3 •.. المزيد
Note:Format should not be hand written.
4. With two cases shown in the following figure: Plot pore pressure with depth for the soils if hydraulic conductivity of soils K1 = 5 x K2. a- b- flow through a unit thickness of the cross-section if K1 = 5 x 10$ (f/s) and K2 = 1 x 10$ (f/s). Estimate the rate of seepage (q) per linear foot of cross-section, i.e. calculate the rate of C- Plot flow net for 2 cases. -z (ft) z (ft) Water Water 3 ft 3 ft Soil 1 1.5 ft Soll 1 Sol 2 3 ft 3 ft 3 ft 1.5 ft Soil 2 Datum psf Datum psf porous stone porous stone 3 ft 1.5 ft 1.5 ft Case 1 Case 2
for the Soil system shown in figure Draw the active lateral earth Pressure diagram lok Pa u 7 0=30 8=18 8 = 3/3/3-4 d=30 sat=20
The section through a long cofferdam is shown below, the coefficient of permeability of the soil being 6x10-8 m/s. Determine the quantity of seepage entering the cofferdam. 5.50 m I 0 1 2 3 4 5 As = 0.70 ml +cl 10 B ax 15 m
the soil profil shwon in figure BI below.determine total and effective vertical stresses and powr water Pressure at Points A, B, and C. For the soil 3m 4m 6m I Sand A5=2167 €=0.69 B C w=9% Silt Gs =2170 = 2₁70 e=0.60 clay = 2.72 @= 0.5 G₁ 5 = 70%
Example 8.2 Refer to the e log o' curve shown in Figure 8.12. a. Determine the preconsolidation pressure, o. b Find the compression index, Ce 1.0 0.9- 0.8 0.7 0.6 03 10 Effective pressure, o (ton/t) (log scale) Figure 8.12