A reheat cycle with two stages of reheating is executed, with steam expanding initially from 90 bar and 530 deg. C. The two reheater pressures are 10 bar and 0.6 bar, and the steam leaves each reheater at 480 deg. C. Condensation occurs at 0.03 bar. For an ideal cycle, find: a. Qa and e b. For the engine, ignore the pressure drop through the reheaters, let the engine operate through the same states, and compute W and e. c. What is the steam flow rate for an engine output of 20,000 kW?

A reheat cycle with two stages of reheating is executed, with steam expanding initially from 90 bar and 530 deg. C. The two reheater pressures are 10 bar and 0.6 bar, and the steam leaves each reheater at 480 deg. C. Condensation occurs at 0.03 bar. For an ideal cycle, find: a. Qa and e b. For the engine, ignore the pressure drop through the reheaters, let the engine operate through the same states, and compute W and e. c. What is the steam flow rate for an engine output of 20,000 kW?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steam power plant is operating on the ideal Rankine cycle. The boiler is maintained at 4 MPa, and the condenser at 40 kPa. The steam quality leaving the turbine is at 90%. a.) Draw the proper T-S diagram of the cycle with proper label for the points. b.) Find the temperature of the steam entering the turbine, Qa, Qr, Wt, Wp, Wnet, efficiency, and steam rate
Q.8 In a regenerative steam cycle employing one open feed heater, the steam is supplied to the turbine as dry saturated at 40 bar, and exhausted to the condenser at 0.35 bar. The intermediate bleed pressure is 10 bar. Sketch the layout of the plant and show on the temp | entropy diagram the pressure under gone by the steam, neglecting the pump works, calculate: A. The mass of steam bled from the turbine per Kg of steam leaving the boiler. B. The thermal efficiency of the plant. C. The thermal efficiency of the plant without feed heating. D. The heat rate in (kJ/kW.hr) for the plant with and without feed heating.
Steam from a turbine with inlet pressure 30 bar and temperature 350°C is bled at 5 bar and 1 bar to supply a two-stage regenerator to heat up condensate leaving the turbine at 0.08 bar. In each stage, the condensate is heated up to the saturation temperature of the bled steam and the bled steam itself condenses completely. Remember: in a regenerator, there is no contact between the two streams, only heat exchange. of Consider the amount of steam bled at 5 bar and 1 bar, respectively, to be m¡ and m2 kg per steam supplied to the turbine. For the first stage, m¡ kg of bled steam at 5 bar heats each kg of condensate arriving from the second stage without any contact (that is, regeneration). Then, m¡ kg of condensate derived from the bled steam drains into the steam space of the second stage at 1 bar without heat loss. The combined drain from the second stage at 1 bar consists of mi+m2 kg per kg of steam supplied to the turbine. The combined drain is cooled to the condenser temperature…
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 16.3846 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Combined work (KW) . Ans.____________________________ Combined steam rate in kg/KW-hr. Ans.___________________________ Actual heat rate( KJ/KW-hr). Ans.____________________________
Write legibly, provide manual step by step solution, and diagram for below given problem. A supercritical power generates steam at 25 Mpa and 560. The condenser pressure is 7 kpa. Determine the exit quality of steam if it expands through a turbine in this power plant. a. 45.66% c. 56.66%b. 68.45% d. 74.26%
Note : similar problem is already solved on bartleby.You can take help from there. Assume ideal and the inlet of pump is saturated liquid.
Find the thermal efficiency of the system in percentage to 2.d.p.
Steam at 10 MPaa, 550 degrees celsius enters an ideal engine that has one stage of regenerative cycle; condenser pressure is 10kPaa and extraction of steam is at 1 MPa. Compute the following 5. Steam rate
please answer 6 to 10
Steam is generated at 10 MPa and 450OC and condensation occurs at 170 kPa. (a)For a Rankine engine operating between these limits, compute the thermal efficiency and the heat rate. (b) Considering that a Rankine cycle occurs between the limits, determine QA, QR, WNet, and eC. (c)What mass flow rate is required for a net output of 35 MW?
A binary-vapour cycle operates on mercury and steam. Saturated mercury vapour at 4.5 bar is suppliedto the mercury turbine, from which it exhaust at 0.04 bar. The mercury condenser generates saturatedsteam at 15 bar which is expanded in a steam turbine to 0.04 bar.(i) Find the overall efficiency of the cycle.(ii) If 50000 kg/h of steam flows through the steam turbine, what is the flow through the mercuryturbine ?(iii) Assuming that all processes are reversible, what is the useful work done in the binary vapour cyclefor the specified steam flow ?(iv) If the steam leaving the mercury condenser is superheated to a temperature of 300°C in a superheaterlocated in the mercury boiler, and if the internal efficiencies of the mercury and steam turbinesare 0.85 and 0.87 respectively, calculate the overall efficiency of the cycle. The properties ofsaturatedmercury are given below :
A reheater cycle is executed of 1 kg steam expanding initially from 12.546 Mpa and540.546oC. The reheater pressures are 2.546 Mpa and the steam leaves the reheaterat 420.546oC. Condensation occurs at 0.02546 Mpa. Calculate W, ec and ee. Ps, please put where the state 1,2 and so on. Make it clear and understandable thank you.