A reheat cycle with two stages of reheating is executed, with steam expanding initially from 90 bar and 530 deg. C. The two reheater pressures are 10 bar and 0.6 bar, and the steam leaves each reheater at 480 deg. C. Condensation occurs at 0.03 bar. For an ideal cycle, find: a. Qa and e b. For the engine, ignore the pressure drop through the reheaters, let the engine operate through the same states, and compute W and e. c. What is the steam flow rate for an engine output of 20,000 kW? (1 bar = 100 kPa)

A reheat cycle with two stages of reheating is executed, with steam expanding initially from 90 bar and 530 deg. C. The two reheater pressures are 10 bar and 0.6 bar, and the steam leaves each reheater at 480 deg. C. Condensation occurs at 0.03 bar. For an ideal cycle, find: a. Qa and e b. For the engine, ignore the pressure drop through the reheaters, let the engine operate through the same states, and compute W and e. c. What is the steam flow rate for an engine output of 20,000 kW? (1 bar = 100 kPa)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q.8 In a regenerative steam cycle employing one open feed heater, the steam is supplied to the turbine as dry saturated at 40 bar, and exhausted to the condenser at 0.35 bar. The intermediate bleed pressure is 10 bar. Sketch the layout of the plant and show on the temp | entropy diagram the pressure under gone by the steam, neglecting the pump works, calculate: A. The mass of steam bled from the turbine per Kg of steam leaving the boiler. B. The thermal efficiency of the plant. C. The thermal efficiency of the plant without feed heating. D. The heat rate in (kJ/kW.hr) for the plant with and without feed heating.
Steam from a turbine with inlet pressure 30 bar and temperature 350°C is bled at 5 bar and 1 bar to supply a two-stage regenerator to heat up condensate leaving the turbine at 0.08 bar. In each stage, the condensate is heated up to the saturation temperature of the bled steam and the bled steam itself condenses completely. Remember: in a regenerator, there is no contact between the two streams, only heat exchange. of Consider the amount of steam bled at 5 bar and 1 bar, respectively, to be m¡ and m2 kg per steam supplied to the turbine. For the first stage, m¡ kg of bled steam at 5 bar heats each kg of condensate arriving from the second stage without any contact (that is, regeneration). Then, m¡ kg of condensate derived from the bled steam drains into the steam space of the second stage at 1 bar without heat loss. The combined drain from the second stage at 1 bar consists of mi+m2 kg per kg of steam supplied to the turbine. The combined drain is cooled to the condenser temperature…
Write legibly, provide manual step by step solution, and diagram for below given problem. A supercritical power generates steam at 25 Mpa and 560. The condenser pressure is 7 kpa. Determine the exit quality of steam if it expands through a turbine in this power plant. a. 45.66% c. 56.66%b. 68.45% d. 74.26%
COMBUSTIONMENGINEERING PROBLEM: Rdirat www A regenerative-reheat gas turbine with intercooling between turbine stages is shown in figure. Air enters at 100 kPa, 300 K with a mass flow rate of 5.807 . The pressure ratio across the two-stage sec compressor is 10. The pressure ratio across the two-stage turbine is 10. The intercooler and reheater each operate at 300 kPa. At the inlets to the Turbine stages, the temperature is 1400 K. The temperature inlet to the second compressor stage is 300 K. The polytropic efficiency of each compressor and turbine stage is 80 %. The regenerator effectiveness is 80 %. č, = 1.005 , k = 1.4 Determine a. The Compressor work, in kg air k/ b. The Turbine work, in- kg air c. The Net cycle work, in- kg air d. The thermal efficiency, in percent e. The work ratio f. The The net power developed, in kW E- Draw the corresponding cycle diagram on the pv plane.
Given in Table are the pressure and temperature of the steam as it enters the turbine as well as the pressure in the condenser. The given engine operates on a simple ideal Rankine cycle, calculate the unknowns in Table. Show solution Rankine Pressure of Temperature Pressure at the Net work Heat Thermal entering the Efficiency (n) in % the steam entering the entering the condenser system (WN) boiler (Qin) turbine (Rx) turbine (t+) in MPa Engine of the steam done by the in KJ/kg in KJ/kg (Pe) in kPa in °C A 3 350 75
Note : similar problem is already solved on bartleby.You can take help from there. Assume ideal and the inlet of pump is saturated liquid.
1. Steam is delivered to an engine at 5.4 MPa and 600°C. Before condensation at 31°C, steam is extracted for feedwater heating at 0.60 MPa. For an ideal cycle, find: (A) Amount of steam extracted (B) Wnet (C) eth
Steam at 10 MPaa, 550 degrees celsius enters an ideal engine that has one stage of regenerative cycle; condenser pressure is 10kPaa and extraction of steam is at 1 MPa. Compute the following 5. Steam rate
3. Consider a reheat cycle utilizing steam. Steam leaves the boiler and enters the turbine at 4 MPa, 400°C. After expansion in the turbine to 400 kPa, the steam is reheated to 400°C and then expanded in the low pressure turbine to 10 kPa. Determine the cycle efficiency. Ans. 35.9%
please answer 6 to 10
Steam is generated at 10 MPa and 450OC and condensation occurs at 170 kPa. (a)For a Rankine engine operating between these limits, compute the thermal efficiency and the heat rate. (b) Considering that a Rankine cycle occurs between the limits, determine QA, QR, WNet, and eC. (c)What mass flow rate is required for a net output of 35 MW?
A binary-vapour cycle operates on mercury and steam. Saturated mercury vapour at 4.5 bar is suppliedto the mercury turbine, from which it exhaust at 0.04 bar. The mercury condenser generates saturatedsteam at 15 bar which is expanded in a steam turbine to 0.04 bar.(i) Find the overall efficiency of the cycle.(ii) If 50000 kg/h of steam flows through the steam turbine, what is the flow through the mercuryturbine ?(iii) Assuming that all processes are reversible, what is the useful work done in the binary vapour cyclefor the specified steam flow ?(iv) If the steam leaving the mercury condenser is superheated to a temperature of 300°C in a superheaterlocated in the mercury boiler, and if the internal efficiencies of the mercury and steam turbinesare 0.85 and 0.87 respectively, calculate the overall efficiency of the cycle. The properties ofsaturatedmercury are given below :