A refrigeration system is to be used to constantly maintain a space at -13°C in an industrial cooling space. The estimated cooling rate of 83362 kJ/h when the outside temperature is 20°C. Determine the minimum power required to drive this refrigerator if analysis is based on Carnot cycle. Provide answer to 2 decimal places and insert the unit symbol in kW. insert minus in answer and use 1°C=173 K if necessary.

A refrigeration system is to be used to constantly maintain a space at -13°C in an industrial cooling space. The estimated cooling rate of 83362 kJ/h when the outside temperature is 20°C. Determine the minimum power required to drive this refrigerator if analysis is based on Carnot cycle. Provide answer to 2 decimal places and insert the unit symbol in kW. insert minus in answer and use 1°C=173 K if necessary.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Handwritten sol-please
A hammer has a speed of 8.0 m/s just before it strikes a 0.015 kg iron nail horizontally, using its 1.2 kg head. Assuming the nail absorbs all of the energy from the hammer, how much would the temperature of the nail rise if the hammer hit the nail 8 times in quick succession? Enter your answer in either K or °C. (Since it's a change in temperature, these units are identical.) J kg.K The heat capacity of iron is 450-
Mechanical engineering thermodynamics. Please show the clear work in handwritten format. Question : A heat engine that rejects waste heat to a sink at 500 R has a thermal efficiency of 25 percent and a second-law efficiency of 50 percent. Determine the temperature of the source that supplies heat to this engine.
Please answer it in 1hr. show solution step by step and the UNITS. Thermodynamics
Oxygen (molar mass 32 kg/kmol)expands reversibly in a cylinder behind a piston at a constant pressure of 3 bar. The volume initially is 0.0148 m and finally is a.0333 m the initial temperature is 18.54 °C Calculate the specific gas constant with the correct unit to two decimal places. Assume oxygen to be a perfect gas and take the specific heat at constant pressure as- 0 .917kJ/kgK and molar gas constant as - 8.314 J/ kmol K
Read and understand each statement carefully. Provide all necessary solutions. Only thermodynamic properties such as specific volume, specific internal energy, specific enthalpy, and specific entropy should be expressed in five (5) significant figures when encountered in an intermediate solution; otherwise, do not round your intermediate solution. Write the final answer in THREE DECIMAL PLACES except for specific volume, specific internal energy., specific enthalpy, and specific entropy that should be expressed in FIVE (5) SIGNIFICANT FIGURES. Use the system of unit predominant in each problem. Box your final answer Question 6 Water at 2.5 MPa and 200°C is heated at constant temperature up to a quality of 80%. Find the quantity of heat received by the water in kJ/kg.
Completely solve and box the final answer. Please show the units to show the unit cancellations. Write legibly 3. A power plant station has a turbine output of 70,000 KW. A dry and superheated steam is supplied to the turbine at 7,000 kpa and 700ºC. The steam was extracted from the turbine at 0.70 bar saturated pressure. Compute the over-all Rankine cycle efficiency (%).
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
Solve the following problems using the standard format (Given, Required, Solution). BOX YOUR FINAL ANSWERS. Do not round off intermediate answers. Round off your final answers to four decimal places. Draw all pertinent diagrams. Use T (K) = T (°C) + 273. In a steam power plant, 1 MW is added in the boiler, 0.58 MW is taken out in the condenser and the pump work is 0.02 MW. Assuming all processes involved are reversible, calculate the thermal efficiency, in %. Answer: Nth = %
11-A piston-cylinder assembly initially contains refrigerant-134a (R-134a) at a pressure of 0.8 MPa and a temperature of 60°C. In the system where the piston can move freely, the temperature of R-134a is reduced to 32°C.Which of the following diagrams correctly represents the process?
SHOW THE TABLE USED! A fixed amount of carbon dioxide goes through a polytropic process where n=1.4. The initial temperature of the CO2 is 250 K. The final temperature of the CO, is 400 K. If the mass of the CO2 is 12 kg and behaves as an ideal gas, determine the work, the change in internal energy, and the heat transfer during the process (in kJ). Note that PV=mRT. In this problem, can the carbon dioxide be considered an ideal gas at the initial conditions if the initial pressure is 150 kPa? Justify your answer quantitatively.
A certain system losses heat to the surroundings at the rate of 150 Watts for 3 hours. The amount of heat the system lost during that time is 1620 kJ. Select one: O True O False