A rectangular suppressed weir, 1 meter in length is used in a reservoir with an area of 50 square yards. During dry season, it was requested for 40 cubic meters of water to be discharged using the weir. If the discharge coefficient is 0.72 and tAhe initial head of the weir was 1.20m, determine the final head acting on the weir after the said volume was discharged and the time it takes to discharge this amount of volume in seconds. A. 0.24 meter and 43.85 seconds B. 7.07 meter and 6.14 seconds C. 0.178 meter and 37.27 seconds D. 3.26 meter and 0.79 seconds

Q: Draw the frontside and topview the Shape Shown

A: Asked: To draw the front, side and top view of the given shape.   The required engineering id drawn…

Q: Draw the minimum number of views necessary to represent the figure (top, front and / or right view)

A: We can represent a 3 D diagram in 2D by  minium of 3 views  Top view Front view Sode view (Right or…

Q: Draw the isometric figure of the given multiview projection. HRP FRP ==== ====== FRP PRP 1 11

A: The multi view projections are given.Multiview Projection:A Multiview Projection is a technique of…

Q: TOP SE THAT Show Transcribed Text FRONT SIDE se isometric paper to construct engineering isometric…

A: Isometric view of given will draw in next step

Q: owing 'shapes', determine the follow , A tion of centroid; xeft, rightYbot roidal Moment of Inertia;…

A:

Q: What dimensioning rules apply to isometric drawings?

A: Use of isometric drawings - 1. It gives clear understanding of the drawn object. 2. In an isometric…

Q: Choose the correct front view for the given drawing

A: i drawn rough sketch of front view   see it in below step

Q: Draw the orthographic views of the object shown.

A: Orthographic Projection: It is the most common method which represents three-dimensional objects. It…

Q: Draw and Isometric view of a hexagonal pyramid of side 30 mm and height 50 mm

A: The isometric view is the three dimensional projection of the object in two dimension vies.  And the…

Q: What is the length of the vertical piece halfway between C and D in feet? B 12'-0" A 16'-0" D 16'-0"…

A:

Q: how did they get grid 1-4 under beams ?

A: Solution: For beam the X and Y are the cordinates where the moment are to be calculated: Grid X…

Q: Draw the multiview projection of the given isometric figure. L HRP FRP L L FRP PRP 1. Discuss how…

A:

Q: Draw the top, the front, and the right side orthographic views of the objects shown. Indicate when…

A: Top , front and side views of the given object can be drawn as

Q: draw a structural base in a picture

A: Structural layout shows the structural components of a building like beams & colums. This layout…

Q: What is orthographic view elaborate? Draw orthographic view of the given figure assuming any…

A:

Q: If a standard view in a drawing has hidden lines, then creating a sectional view is always…

A: Sectional view represents the internal configuration of any object. It shows the details of all…

Q: Given the isometric view of the cut block objects shown, use rectangular grid paper to sketch a…

A:

Q: structural drawing   please indicate a details in this image

A: The structural diagram is shown in the above figure. We have to indicate a details in this image.

Q: Draw the front and top and side view for these?

A: For any object which is needed to be constructed or manufactured it is important to have drawings…

Q: According to Francis Ching, what is an interior elevation? An orthographic projection of a…

A: Francis D.K. Ching was a registered architect and a well known Professor Emeritus at the University…

Q: SKETCH AUXILIARY VIEW. SHOW ALL VISIBLE AND HIDDEN LINES.

A: An auxiliary view is simply known as the “helper” view because it shows the slanted part of the…

Q: Civil Engineering Using the drawing board, draw the following views in 3rd angle projection: a) An…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: Draw the front, side, and horizontal projections

A:

Q: O mm 10 mm FIGURE 1

A: Always side view is drawn beside the front view because Height of the object will be equal . Front…

Q: (D) -

A: A sectional view in engineering drawing is a representation of an object as if it were cut by an…

Q: Describe Mohr’s Circle.

A: Mohr’s circle is defined as a two-dimensional graph which represents stresses at a point.

Q: Where is the top view?

A:

Q: draw an isometric view of HEXAGONAL PRISM  where the base is 25mm and height 50mm.

A: Isometric view: It is also known as isometric projection. It is defined as the visual representation…

Q: Instructions: Redraw the objects in isometric orloblique views. Also, draw the three basic…

A:

Q: Draw a detailed layout of a column formwork with dimensions.

A: The solution is in step 2:

Q: Differentiate Isogonic and agonic lines?

A: The terms isogonic and agonic are related to geological engineering.

Q: PART 1. AREA & VOLUME OF PRISMS Draw the indicated views for the isometric drawing below. Isometric…

A: An isometric view is given, we need to draw: 1. Top view 2. Left view 3. Front view

Q: Draw the minimum number of views necessary to represent the figure (for example top, front and / or…

A: To represent a 3D diagram in 2D we need three views  Top view Front view  Right or left side view…