A rectangular scow 2.13 m high, 5.5 m wide and 9.8 m long loaded wit center of gravity is 0.6 m above the waterline. What is the initial metac Select one: a. 0.66 m b. 0.30 m C. 0.76 m d. 0.60 m

Q: At a hydraulic jump, the depths at its two sides are 0.3 m and 1.2m. The head loss in the jump is B…

A: Given- depths-y1=0.3 m,y2=1.2 m, It is needed to find the head loss in the jump.

Q: Using the method of components calculate the magnitude, direction, and location of the total force…

A: Given:- H=20m specific weight of water =1t/m3 specific weight of concrete=2.6t/m3 To find:- a)…

Q: . A concrete dam retaining water is show in the figure. If the specific weight of concrete is 23.5…

A: Given above figure with specific weight of concrete = 23.5 kN/m3

Q: 16.3

A:

Q: K= 2 x 10³ cm/sec 2. Elev. = 100 shale (impermeable) b he h₂ A 14' 65 B Fill in the blank total,…

A: A flow net for underground flow is given below, Total equipotential drop, ND = 7 Total flow…

Q: a block (unit weight = 19.5 kn/m3) 0.55m square and 479mm deep floats on a stratified liquid…

A:

Q: Complete the table with solution please)

A:

Q: b) Write the compatibility equation of the structure in figure 2. SKN 10KN/m 2.5m 25m 2.5m Figure 2

A:

Q: Theory of structure Drow S.F.d A.F.D B.M.D

A: Given Data  Draw axial force, Shear force and bending moment diagram.

Q: Question attached

A: Solution: Capillary risehc=4σCosθγdhere,γw=9810 N/m3σ=Surface tension=0.075 N/md1=0.00075…

Q: An 8m-Thik layer of stiff saturated clay is underlain by a layer of sand (Refer to the figure…

A:

Q: A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of…

A:

Q: The pore water pressure (kPa) at D due to capillary rise is y = 16.0 kN/m? Ysat = 16.5 kN/m3 0.5 m D…

A:

Q: An open ended steel barrel of 1 m height and 1 m diameter is filled with saturated fine sand having…

A: An open-ended steel barrel- Height = 1 m, & Diameter d = 1 m, Drop in the water level h = 0.75 m…

Q: a hydraulic jump, the depths on the two sides e 0.4 m and 1.4 m. The head loss in the jump is early?

A: Depth,  y1 = 0.4 m  and y2 = 1.4 m

Q: 1. Compute the specific gravity of the wooden board 2. Compute the length submerged in oil for…

A: Given: The cross-section area is 0.005 m2. The weight is 30 N/m.

Q: 1. Portal Method The frame shown is subjected to lateral loads as shown. Supports S, T, U V, W and X…

A: To Find the Forces in the frame member

Q: masonry dam

A: given data,masonry dam is giventop width of dam= 60 cm = 0.6 mbottom width of dam =3.7 mheight of…

Q: A cast iron pipe of external diameter 300 mm has walls 10 mm thick and is required to carry water to…

A: Given that:*External diameter of pipe D=300mm*Internal diamter of pipe d=300mm-10-10=280mm*Failure…

Q: SITUATION 3 Consider a 8-m long, 8-m-wide, and 2-m-high above ground swimming pool that is filled…

A:

Q: A rectangular scow 12-m long, 7.20m wide, and 2.40m 1.50m above the bottom. It carries a total load…

A:

Q: Q2/ For the soil profile, find the: 1- Total pressure (o.). 2-Pore water pressure ou (u). 3-…

A:

Q: Two points exist under the water’s surface within a reservoir. Point A is at a depth of 155.2’,…

A: Applying Bernoulli's equation between two points: PAγ+vA22g+zA=PBγ+vB22g+zBwhere,γ=62.4 lbft3g=32.2…

Q: 3m 3m 1m 1m 1m 4m

A: Unit weight of concrete, γc =24KNm3No hydrostatic lift it means no upward seepageUnit weight of…

Q: Assume a load of 4,000 tons applied as a point concentration at the surface near the MSU Golf…

A: Use boussinesq equation.

Q: A sphere 1m in diameter floats half submerged in tank of oil (SG-0.80). What should be the weight of…

A: Specific Gravity : Specific Gravity, often known as relative gravity, is a dimensionless quantity…

Q: A 3m dam holds water at a a certain depth, The base of the dam is 5m and the cr 0.7, at what height…

A: GIVEN- d=3mb=5mμ=0.7

Q: Estimate the equivalent hydraulic bearing for flow in the vertical direction. Suppose that k1= 10 x…

A:

Q: A masonry dam with base 6 m wide is subjected to a total horizontal force of 320 kN and a total…

A:

Q: What is the power transmitted by a 100 mm diameter solid shaft at 150 rpm without exceeding a…

A: Given- Dia d=100 mm,Speed N=150 RPM,Maximum stress=60 N/mm2,π2=10, It is needed to find the Power P.

Q: 1,0 m 5 m 4 m I NININININININININI. Dry bark clay i Sa Ysat =15 kN/m³ SiMr Ysat y 18 kN/m³ PVP = 21…

A:

Q: The section of a gravity is as shown in the figure. Assume hydrostatic uplift to vary uniformly from…

A: H = 60' Density of water= 9.81KN/m3 = 62.4lb/ft3  U = 1/2*Density of dam*H*B*1 (where, H = ht of…

Q: nalyse the stability of concrete gravity dam shown in the figure for the usual and unusual loa

A: Given Data f=0.85                  σc=30000 kn/m2ϕ=0.6                     αf=4000kn/m2ζs=6000kn/m2…

Q: For the following data: • Maximum water level = 28 m • Unit weight of water = 10 kN/m³ • Unit weight…

A: 1. stress criteria Total forces acting on dam are; Weight of dam, W = (1/2)× b ×H ×γc Where b =…

Q: Q2/ For the soil profile, find the: 1- Total pressure (o.). 2-Pore water pressure ou (u). 3-…

A:

Q: PROBLEM 1: The homogeneous structure shown weighs 21.45 kN per square meter of cross-section. The…

A: Weight of cross section (y) = 21.45 KN/m2Determinea. The equivalent force of uniform load P1.b.…

Q: Problem: Determine the additional force when the solid concrete ABCD (Yconcrete= 24 KN/m) is added…

A: Calculating the force acting on  solid concrete due to water assuming thickness of concrete = 1m…

Q: For the setup shown, if 40% of the total head is lost in flowing through soil B which has a…

A: Answer  (A) Let us first calculate elevation head(he), pressure head (hp) and Total head(ht)…

Volumes

Volume usually is the dimensional quantity that involves the evaluation of any three-dimensional figure enfolded inside a closed space. The SI unit (International System of Units) of volume is m3 and the dimensional unit of volume is [L3]. For estimation of the volume of any figure, various formulae are used. Another application of volume includes the reference in the sound levels, the higher the sound intensity, the louder the sound heard, and hence, the larger the volume. The SI unit of sound volume is decibels (dB).