A rectangular column of 80 mm x 100 mm size is braced at the mid-point along its weaker direction. Determine the critical axial load the column can support with pin-ended conditions over a length of 3.25 m. The modulus of elasticity of the material is 20 GPa.

A rectangular column of 80 mm x 100 mm size is braced at the mid-point along its weaker direction. Determine the critical axial load the column can support with pin-ended conditions over a length of 3.25 m. The modulus of elasticity of the material is 20 GPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: For the following composite beam which is built up out of two wooden beams and three steel plates,…

A: Given- For Wood- E = 15 GPa σmax = 7.5 MPa For Steel- E = 200 GPa σmax = 150 MPa To Find- Moment…

Q: 17. A rectangular bar is loaded as shown. Find the maximum tensile stress developed ove section A-A.…

A: Given : Max. tensile stress developed over section A-A ?

Q: Is this a frame or a truss? Calculate the cross section of the bar BC if the allowable normal stress…

A: Given:- Allowable normal stress in BC = 165 MPa To determine- a) Is this a frame or a truss? b)…

Q: Determine the stress in each of the two vertical rods if the temperature rises 50 °C after the load…

A: To determine the stress in each of the vertical rods. Given, Rise in temperature (∆T) = 50oC Load…

Q: A 16 mm steel bar AB and a 25 mm steel bar BC support a load P = 7,500 N as shown. If E = 200 GPa,…

A: Given data: Diameter of AB steel bar=16 mm Diameter of BC steel bar=25 mm Load=7500 N It is asked…

Q: SAMPLE PROBLEM 2: VSE LRFD Steel column 3.6m long and hinged at both ends is used to carry an axial…

Q: A high-strength steel band saw, 22 mm wide, runs over pulleys 1100 mm in diameter. What minimum…

Q: A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as…

A: The given data is as follows: E=200 GPaAllowable stress in rod CD=124 MPa

Q: The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was…

Q: The limit of proportionality in the material of a structural steel member, when subjected to simple…

A: Given data- A structural steel member- Simple tension-σy=280 N/mm2Principal stress-σ1=122 N/mm2…

Q: Determine the shear stress on the a-a plane. 45 MPa 30° a (а) -10.5 МРа (b) 10.5 MPа (c) -50.3 МРа…

A: Shear stress on plane a-a is given by ζxy'=σy-σx2sin2θ+ζxycos2θwhere θ=angle of inclination of…

Q: A 2-m long steel rod, 10-mm in diameter, is carrying a load of 20 kN. (a) what is the axial stress…

A: This question is related to the Strength of material. In this question we calculate axial stress and…

Q: If M=6kip.ft, determine the maximum tensile stress in the beam shown in the figure below

A: DETERMINATION OF MAXIMUM TENSILE STRESS IN THE BEAM

Q: A composite shaft consists of an aluminum jacket “t” mm thick and a steel core 50 mm in diameter.…

Q: The composite beam shown in the figure is simply supported and carries a total uniform load of 40…

A: In composite beam, bending strain diagram is linear and strain compatibility conditions is used to…

Q: A solid aluminum shaft of 120 mm diameter fits concentrically in a hollow steel tube. Determine the…

Q: 160 kN LLET --3m-> -6m 400 kN 6m X 40 mm 200 mm 100 mm 20 mm

Q: The belt shown has a width of 43 mm and a thickness of 6 mm. [P1= 30 kN, P2= 6 kN, P3= 14 kN, P4= 14…

A: the width of the belt (b)=43 mm, thickness (t)=6 mm.P1=30 kN, P2=6 kN, P3=14 kN, P4=14 kN.…

Q: A high-strength steel band saw, 23 mm wide, runs over pulleys 800 mm in diameter. What minimum…

Q: 1. For the beam shown, a. determine the maximum flexural stresses in compression ant tension. b.…

Q: Design the column wooden section with 3.5 m in length Fixed at both ends. Use the given allowable…

A: Solution:- Load carrying capacity of a short column ( R.C.C), P = σsc.Asc+σcc.Ac but here wooden…

Q: solve Any numerical problem on stresses and strains for multiaxial loading conditions.

A: Consider a bar of elastic material subjected to direct compression stress, σ in longitudinal…

Q: 3. Two bars are made of a material with the stress-strain diagram as shown. Find the cross-sectional…

A: Given :

Q: A high-strength steel band saw, 26 mm wide, runs over pulleys 700 mm in diameter. What minimum…

Q: A steel structural member is to be used as a column 5 m long. The column is to be pinned at both…

A: Perry-Robertson equation Perry-Robertson equation is the mathematical relation which can used in…

Q: Determine the maximum tension and compression stress for the aluminum double stem T section shown…

Q: The cross-section of a pretensioned prestressed concrete beam is shown in figure. The reinforcement…

Q: For the beam shown, a. Determine the maximum flexural stresses in compression and tension. b.…

Q: Design the column wooden section with 3.5 m in length Fixed at both ends. Use the given allowable…

A: L = 3.5 m or 3500 mmP = 85 kN or 85000 N F'c = 15 MPaE = 14000 MPa

Q: An 8 m simple beam is loaded with a 208 kN point load at the first third of its length. The cross…

Q: A steel loop ABCD is placed around a 1.0 in. diameter aluminum rod AC. Cables BE and DF, each of 0.5…

A: D = 1 in d = 0.5 in 13 ksi

Q: A hollow circular section, of external diameter 200 mm and thickness 20 mm is used as a beam. The…

A: Given data, External diameter = 200 mm Thickness = 20 mm Internal diameter = 160 mm Maximum bending…

Q: The thin-walled vessel shown is fabricated by joining two cylinders with thickness 26 mm using 20…

A: Given, Thickness of the vessel, t= 26mm Number of bolts= 20 Diameter of the bolts= 20mm Outer…

Q: Problem 3: A rectangular column with a width of 3 in. and a depth of 6 in. is pinned at both ends…

A: Given: Column pinned at both ends E= 10000Ksi Width 3 inch and depth 6 inch Length 20 ft…

Q: A high-strength steel band saw, 22 mm wide, runs over pulleys 700 mm in diameter. What minimum…

A: First we summarise the given data : Width of Steel Band = 22 mm Diameter of pulleys = 700 mm…

Q: A rectangular beam has a design moment of 40 kNm. The material has a 200 MPa yield strength. Create…

Q: A so-called "trapeze bar" in a hospital room provides a means for patients to exercise while in bed…

Q: Is this a frame or a truss? Calculate the cross section of the bar BC if the allowable normal stress…

A: Normal stress= 165 MPa To determine- a) Is this a frame or a truss? b)…

Question

A rectangular column of 80 mm x 100 mm
size is braced at the mid-point along its
weaker direction. Determine the critical axial
load the column can support with pin-ended
conditions over a length of 3.25 m. The
modulus of elasticity of the material is 20
GPa.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A high-strength steel bar used in a large crane has a diameter d = 3.00 in. (see figure). Ⓡ The steel has a modulus of elasticity E = 29 x 105 psi and Poisson's ratio is y = 0.27. Because of clearance requirements, the diameter of the bar is limited to 3.002 in. when it is compressed by axial forces. What is the largest compressive load Pmax that i permitted? Assume that the material behaves linearly elastically. (Enter the magnitude in lb.) lb
il Engineering Dept. /Second Year "Strength of Materials" Home Works: A flat steel bar has axial loads (forces along the centroidal axis of the bar) applied at points A, B, C, and D, as shown in Fig. a. If the bar has a cross-sectional area of 3.00 in.², determine the normal stress in the bar (a) On a cross section 20 in. to the right of point A. (b) On a cross section 20 in. to the right of point B. (c) On a cross section 20 in. to the right of point C. Figure (a) 81 kip 30 in. 45 in. OA BOC 18 kip 54 kip 40 in. (a) Do Prof. Dr. Qais Fadhil 45 kip
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
A simple pin-connected truss is loaded and supported as shown. The load Pis 240 kN. All members of the truss are aluminum pipes that have an outside diameter of 130 mm and a wall thickness of 14 mm. Determine the normal stress in each truss member. Assume truss dimensions of a = 10 m, b = 6.25 m, and c= 5 m. Tensile stress is positive, while compressive stress is negative. b D Answer: OAB 11 JAC OBC= OBD = OCD = i M M a B MPa MPa MPa MPa MPa
The column above is subjected to axial loading only. Assume the following: • E= 29000 ksi G = 10000 ksi • = 986 in4 A = 60 in? • L= 20 ft • Grade 60 steel (60 ksi yield stress) • The column is fixed at the top and pinned at the bottom Which of the following is closest to the maximum normal stress the column can support (before yielding or buckling)? 167 ksi 24 ksi 42 ksi 60 ksi
Q/ Find the Maximum stresses in Steel and Aluminum. Est= 210G pa and E al%3D 70 G pa ? W= 15 Kn.M 120mm 5m Al steel 60mm 140 mm
According to IS 800-1962 the permissible bending stress in steel slab plate is (b) 1420 kg/cm² (d) 1890 kg/cm² (a) 1500 kg/cm² (c) 2125 kg/cm²
Please show full solution, thank you
d(mm)=65 T(nm)=1500 Gst(Gpa)=70
3. An ASTM A36 structural steel beam 5.00 m long is placed between two rigid supports. When the temperature is 20°C, there is no stress in the bar. Compute the stress developed in the beam if the temperature rises to 45°C. Assume that the proportional limit is 235 MPa. a = 11.7 x 10-6 1/C° E = 207 GPa 4. In question 3, assume that the bar is free to elongate or shorten, calculate the change in the length of the bar if the temperature drops from 20°C to -20°C.