A rectangular block of a material with a modulus of rigidity of FN ksi is bonded to two rigid horizontal plates. The lower plate is fixed, while the upper plate is subjected to a horizontal force P. Knowing that the upper plate moves through 0.04 in. under the action of the force, determine (a) the shearing strain in the material, (b) the force P exerted on the upper plate. 2.5 in. 8 in.. 2 in. P

A rectangular block of a material with a modulus of rigidity of FN ksi is bonded to two rigid horizontal plates. The lower plate is fixed, while the upper plate is subjected to a horizontal force P. Knowing that the upper plate moves through 0.04 in. under the action of the force, determine (a) the shearing strain in the material, (b) the force P exerted on the upper plate. 2.5 in. 8 in.. 2 in. P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. A polyethylene bar (E = 1.4 GPa and v = 0.4) having di = 70 mm is placed inside a rigid steel tube having an inner diameter d2 = 70.2 mm. The polyethylene bar is then compressed by an axial load P. (a) At what value of P will the space between the polyethylene bar and the steel tube be closed? (b) If the compressive force P = 50 kN, determine the normal stress on the cylindrical surface of the bar, axial strain and the change in volume in the bar. Steel tube. 7p Ip Polyethylene- bar
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If 0 = 68 MPa, determine the principal stresses acting at the point. 114 MPa 66 MPa 157.9 MPa and -155.4 MPa 82.0 MPa and -83.7 MPa O 121.2 MPa and -138.0 MPa O 167.4 MPa and -98.1 MPa O 133.2 MPa and -131.2 MPa
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If o = 16 MPa in the direction shown, determine the principal stresses at the point. 10 MPa 26 MPa O 35.56 MPa and -14.11 MPa 54.80 MPa and -17.81 MPa O 27.65 MPa and -9.78 MPa O 46.71 MPa and -11.05 MPa O 39.17 MPa and-13.17 MPa
Steel Tank with an outside diameter of 600 mm has a wall thickness of 8 mm. The tank is used as storage of gas under pressure of 2.2 MPa. a. Determine the value of the tangential stress in the tank wall Determine the value of the longitudinal stress in the tank wall b. 30 mm helt hand
A steel rod of length = 3m, diameter - 300 mm and modulus of elasticity = 200 GPa is inserted into an aluminum tube. The aluminum tube as length = 2999.95 mm, wall thickness of 20 mm and modulus of elasticity of 70 GPa. a.) Determine the deformation of each member due to axial compressive force P-100 KN. b.) Determine the stress in each member. c.) Determine the axial strain if no gap exists.
A steel rod of length = 3m, diameter - 300 mm and modulus of elasticity = 200 GPa is inserted into an aluminum tube. The aluminum tube as length = 2999.95 mm, wall thickness of 20 mm and modulus of elasticity of 70 GPa. a.) Determine the deformation of each member due to axial compressive force P-100 KN. b.) Determine the stress in each member. c.) Determine the axial strain if no gap exists. WITH FULL SOLUTION ASAP PLEASE
To lower ends of the three bars in the figure two are the same level before the rigid homogeneous W=176kN block is attached. Each still bar has a length of 1.00 m, an area 500mm² and E=200 GPa. For the bronze bar the length is 1.6m, the area is 900mm² and E= 83 GPa. What is the stress developed in the bronze bar? What is the stress developed into steel bar? What is the elongation of each bar?
(c) A thin, triangular plate ABC is uniformly deformed into a shape ABC', as shown by the dashed lines in the figure. Calculate (i) The normal strain along the centreline OC; (ii) The normal strain along the edge AC; and (iii) The shearing strain between the edges AC and BC. b 0-1 b B 90° 10.001b
QUESTION 2. An oblique bending moment of M = 5 kN.m is applied on the cross-section of an aluminum beam as shown in the figure. (a) Calculate the maximum values of compressive and tensile normal stresses on the cross section. (b) Define the orientation of the neutral axis and draw on the cross-sectionç. M = 5 kN.m 30° 10 mm 40 mm y 10 mm At-40 mm-- 30 гу 30 mm 10 mm 10 mm
%3D QUESTION 2. An oblique bending moment of M = 5 kN.m is applied on the cross-section of an aluminum beam as shown in the figure. (a) Calculate the maximum values of compressive and tensile normal stresses on the crss section. (b) Define the orientation of the neutral axis and draw on the cross-sectionç. M = 5 kN.m 30° 10 mm 40 mm 10 mm A-40 mm--r: 30 mm 30 mm 10 mm 10 mm
The beam has a rectangular cross section and is subjected to the loading shown. Determine the components of stress ox, oy, and Txy at point B. 800 N B 1000 N 15 mm 20 mm 20 mm 15 mm 100 mm 10 mm
6. Due to a loading, the plate is deformed into the dashed shape shown in the figure below. Determine (a) the average normal strain along the side AB, and (b) the average shear strain in the plate at A relative to the x and y axes. 0.13 in В 0.09 in 10 in A 12 in C