A radio for each of the two RF bands that are supported by an access point's radios has a total of six spatial streams. What is the total number of antennas that are included inside this access point?

A radio for each of the two RF bands that are supported by an access point's radios has a total of six spatial streams. What is the total number of antennas that are included inside this access point?

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter8: Data And Network Communication Technology

Section: Chapter Questions

Problem 10RQ

See similar textbooks

Related questions

Q: An access point's radios support two RF bands with six spatial streams each. This access point has…

A: Answer: Radiation Patterns (RF) With frequencies ranging from 300 gigahertz (GHz) to 9 kilohertz,…

Q: Data communication In a system with a bit rate of 3Mbps ,it is desired to send 3 bits at once…

A: In this question we have to solve for the given data. Calculate the levels, baud rate and bandwidth…

Q: Explain the ARP procedure that occurs when a frame is sent.

A: ARP (Address Resolution Protocol ) is a network protocol used to distinguish a device's hardware…

Q: Evaluate the modulation dep Calculate the carrier power, Draw the block diagram mathematical…

A: Evaluate the modulation depth m, and mention the type of this AM system. The modulation depth (m)…

Q: A channel has a frequency range between 3 KHz and 14 KHz. The SNR in this channel is 25 dB. Find the…

A: ANSWER:-

Q: The electrical connection is considered to have a parallel interface when it can transmit eight or…

A: Parallel Interface: A multiline channel which can be able to send multiple bits of data…

Q: 2. What is the bandwidth of a signal that can be decomposed into five sine waves with frequencies at…

A: The answer for the given question is as follows.

Q: If eight or more bits of information may be sent across the electrical connection concurrently, we…

A: Here is your solution -

Q: Attenuation in fiber systems is a comparison, or ratio, of input and output power levels for optical…

A: The attenuation of a fiber system is a measure of the signal loss that occurs as light travels…

Q: A flash memory of 16 Gbyte is used to store PCM voice data. Suppose that a CT voice signal is…

A: How many minutes of the voice signal can be stored (as PCM data) in this memory? For 12-bit, we…

Q: signal is carrying data in which one data element is encoded as one signal element (r = 1). If the…

A: The formula used here is s=C*N*(1/r) here N=200kbps which is 200000 r=1

Q: In a typical mobile phone system with hexagonal cells, it is forbidden to reuse a frequency band in…

A: Consider that a typical mobile system is designed with hexagon cells and it is available with 840…

Q: Еxample: A telephone line has a bandwidth of 3000. The signal-to-noise ratio is usually 3162. For…

A: The formula for channel capacity is c=wlog2(1+s/n) s/n is signal to noise ratio and w is the…

Q: A voice channel occupies a bandwidth of 28 kHz 10 voice channels are to be multiplexed together…

A: FDM is a technique used in telecommunications and signal processing to combine multiple signals into…

Q: . A receiver block diagram for a certain analog voice communication system is shown below. The SNR…

A: the loss in decibels due to free space propagation given by the formulaFSPL(db) = 20 • log10(d) + 20…

Q: Consider a geostationary satellite-based system. Earth stations are multiplexing digital information…

A: Given ,A geostationary satellite-based system .And a earth station is multiplexing the digital data…

Q: The Modem is the most well-known kind of Data Communication Equipment. It modulates an analog…

A: Introduction: A modem is a physical device that translates digital data into a transmission medium…

Q: A signal is carrying data in which one data element is encoded as one signal element (r 1). If the…

A: The baud rate, often known as the signal rate, can be represented as: S=c×N×1r bauds where N denotes…

Q: The horizontal sweep oscillator frequency, vertical sweep circuit frequency and the spectrum…

A: A sweep generator is a piece of electronic test equipment similar to, and sometimes included on, a…

Q: 45. Consider the GPIB interface between a talker and a listener as shown in Figure 13-86(a). From…

A: Given:

Q: optic cable

A: Given :- A fiber optic cable has a loss of 16 dB per kilometer and a cable length is 2,000 feet…

Q: A synchronous data frame does not contain a(n)(a) preamble (b) data field(c) address (d) vector…

A: Vector field

Q: Suppose a signal travels through a transmission medium and its power is reduced to one-half. What…

Q: We would like to design a bandpass filter in a DSP system which attenuates a signal outside the…

A: (a). This is because the maximum bandwidth for any input signal is 5000 Hz, and the Nyquist theorem…

Q: A flooded frame's destination address is frequently unclear

A: An ARP request is used to determine the target host's MAC address on an Ethernet LAN. A switch will…

Q: An analog signal in sine form is intended to be transmitted to the receiver by pulse code…

A: Given, peak to peak amplitude = xxx volts. Frequency of signal = xxx Hz Medium Height = xxx level…

Q: Now suppose you have a composite signal (composed of many frequencies). If the frequencies range…

Q: Consider a communication channel with bandwidth B = 8000 Hz. Suppose the channel has a…

Q: A digital radio communication system receives a signal with signal power S of 3 µW, and noise level…

A: Given signal power S = 3 µW noise level N = 200 nW

Q: An analog signal in sine form is intended to be transmitted to the receiver by pulse code…

A: 1) - Theoretical Value of sampling frequency is always equal to 2 times the signal frequency. Hence…

Concept explainers

Network transmission cabling

A network is a collection of devices connected by communication links. A device can be a computer or any instrument capable of sending and receiving data or information formed by other nodes toward the network. A channel that connects people or things is known as a network. It sends the data from one place to another. It is the basic concept of a computer, network, and data communications.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.

Similar questions

The horizontal sweep oscillator frequency, vertical sweep circuit frequency and the spectrum bandwidth of a 625 line TV system are respectively. 7MHZ, 50HZ and 15625HZ O15625HZ, 7MHZ and 50HZ O 15625HZ, 50HZ and 7MHZ O50HZ, 15625HZ and 7MHZ
Example: A telephone line has a bandwidth of 3000. The signal-to-noise ratio is usually 3162. For this channel the capacity is calculated as
My id last two digit =32 so x1x2=32 Subject:Datacommunication
In the computer system, the bus is said to be a collection of wires through which data is transmitted. The bus could be unidirectional or bidirectional depending on what is being done at a time. With referenced to the type of buses explain this phenomena or principle.
10. A receiver block diagram for a certain analog voice communication system is shown below. The SNR at the output of the LPF must be at least 6 dB for the voice to be understandable. The transmitter and the receiver are separated by a line-of-sight path with a distance of 4 km. The antenna at the transmitter and the receiver have a gain of 33 dB each and operates at a frequency of 2.4 GHz with a 20 MHz bandwidth. a. How much is the loss in decibels due to free space propagation? b. If the noise power measured at the antenna is 0.1 pW, what is the noise power at the output of the LPF? c. What is the minimum received power, Pr, in dBm that will make the voice output at the LPF be understandable for the user? d. If the transmit power is 5 W, how much is the link budget? e. What should be the minimum transmit power at the transmitter to achieve a successful communication?
In a typical mobile phone system with hexagonal cells, it is forbidden to reuse a frequency band in an adjacent cell. If 840 frequencies are available, how many can be used in a given cell?
I A channel has a frequency range between 3 KHz and 14 KHz. The SNR in this channel is 25 dB. Find the maximum Bit rate of the channel and the Signal levels. [3 marks] For a bit stream "0 1 1 0 0 1 0 1", sketch the waveforms for (i) NRZ-I - (Assume the initial level at time zero is Low) (ii) NRZ-L - (assume 0 as High and 1 as Low) (iii) RZ Encoding – (Assume the initial level at time zero is Low) [3 marks]
In a computer system, the bus is defined as a set of wires that are used to carry data from one location to another. Depending on what is being done at any one time, the bus could be either unidirectional or bidirectional. Explain this phenomenon or concept in terms of the type of buses that exist now.
If eight or more bits of information may be sent across the electrical connection concurrently, we say that the interface is parallel.
45. Consider the GPIB interface between a talker and a listener as shown in Figure 13-86(a). From the handshaking timing diagram in part (b), determine how many data bytes are actually trans- ferred to the listening device. Talker Listener Data bus DAV DAV NRFD NRFD Transfer bus NDAC NDAC (a) (b) FIGURE 13-86
Attenuation in fiber systems is a comparison, or ratio, of input and output power levels for optical cable, connectors, couplings patch panels, etc., typically expressed in Decibels with the equation; dB = 10log(Pout/Pin). Calculate the attenuation in dB of the following: 9. Pout= .01mw, Pin =1mw; 10. Pout= .5 mw, Pin = 1mw; 11. Pout = .1mw, Pin = 2mw; 12. Pout = .5 mw, Pin = .2mw; dB= ? dB= ? dB= ? dB= ?
An analog signal in sine form is intended to be transmitted to the receiver by pulse code modulation. Answer the questions asked from you by determining the parameters given below. Peak to peak amplitude = xxx volts Signal frequency = xxx Hz Medium height kuantalayıcı = xXx level 1. What should be the theoretical minimum sampling frequency for the signal to be reconstructed in the receiver without distortion? 2. What should be the practical minimum sampling frequency for the signal to be reconstructed in the receiver without distortion? 3. What should be the theoretical and practical minimum sampling frequency if an anti-aliasing filter is used at the frequency of xx Hz you specify before sampling? 4. What is mean square quantation error? 5. Calculate the maximum calculation error. 6. Calculate the maximum amplitude of the probability distribution function of the quantization error. 7. What is the signal to noise ratio? 8. What is the theoretical binary transmission rate? 9. What is…