A PWM signal is required for a motor controller. The PWM is generated by a TPM in a KL25Z. The signal for no motion of the motor is a 10 millisecond period with a 50% dut cycle. Which setup below is NOT a correct setup for a TPM for this starting condition? Ignore the "-1" adjustment for the counts. It is not important in this application.

A PWM signal is required for a motor controller. The PWM is generated by a TPM in a KL25Z. The signal for no motion of the motor is a 10 millisecond period with a 50% dut cycle. Which setup below is NOT a correct setup for a TPM for this starting condition? Ignore the "-1" adjustment for the counts. It is not important in this application.

Computer Networking: A Top-Down Approach (7th Edition)

7th Edition

ISBN:9780133594140

Author:James Kurose, Keith Ross

Publisher:James Kurose, Keith Ross

Chapter1: Computer Networks And The Internet

Section: Chapter Questions

Problem R1RQ: What is the difference between a host and an end system? List several different types of end...

See similar textbooks

Similar questions

Assume we are writing a testbench for a sequential circuit that has three control inputs (cA, cB, cC) and a periodic clock (clk). If we define CLK_PERIOD as a localparameter with a value of 50 (nsec), write the testbench segment that would ensure all possible combinations of the control inputs were tested on a clock rising edge. This is can be done more elegantly if you define each time step in terms of the constant CLK_PERIOD. Your answer should include the statements that define clk, cA, cB, and cC over time. Hint: think of how you would show all combinations of three variables on a truth table and replicate that over time, where each combination is held over a timespan with a clock triggering edge.
Design the interface for a positive logic switch to TM4C123GXL Port A pin 7. Show formulas and calculations for each circuit element. Draw the circuit schematics with components labelled with their names and values. Write the C code as a function to initialize the port for interfacing the switch. Write a function to read the data value of Port A pin 7. Comment your code to explain each initialization step clearly.
Apply 5B: Use a 7-Segment Decoder to Drive a 7-Segment Display 1. Draw the wiring diagram of the 74LS47 device driving the common-anode 7-segment display through 3300 resistors in series, one per segment. 2. Build the circuit based on the wiring diagram. Tie off any control inputs of the 74LS47 device to enable it as a 7-segment decoder. Test all the segments of the display by temporarily connecting LT (pin 3 of 74LS47) to GND. Then connect D, C, B, and A of the 74LS47 device to power or ground rail and cycle through the 16 combinations to verify that the display shows the characters according to the truth table of the 74LS47 device. 3. Now interface the circuit in Apply 5A.4 with the circuit in Apply 5A.2 such that the display only shows the numbers controlled by N3N₂N₁No that are prime. When the numbers are non-prime, the display should be blank. Hint: use a single device with basic gates.
Draw the symbols for a Normally Open (NO) limit switch and a Normally Closed (NC) limit switch, both in the un-actuated and actuated states.
1.1 Design a circuit for the traffic light unit in Multisim. The design should include 3 positive edge triggered D flip-flops. Set your clock signal to 1Hz. Please include Four screenshots of your working circuit, with each screenshot showing each of the light configurations shown in Figure 1. 000 100 010 110 001 Figure 1. A state diagram for a traffic light control The design should include 3 positive edge triggered D flip-flops. Use 1 flip-flop to control the on and off of a given light, and the state machine should switch from Red (100) -> Red and Amber (110) - > Green (001) -> Amber (010) and repeat the cycle again, with the following transition table: Current state Next state 000 100 100 110 110 001 001 010 010 100 ABC A*B*C* Table 1. A transition table for the traffic light unit
An IC (number: ? ) is a parallel adder and is comprised of this number of full adders:_ . Connecting it properly with another IC (containing these gates: ? ) will increase its functionality. Set_? = 0 for subtraction.
Solve number 2
Step2. Using the basic logic circuits, build and test a 2-to-4 decoder circuit corresponding to the following requirements. Requirement 1. The decoder should have 2 inputs labeled as A and B. Requirement 2. The decoder should have 4 outputs labeled as Oo, 0₁, 02, and 03. Requirement 3. The decoder should behave as below: Input A 0 0 1 0 BOLO 1 00 0₁ LOOO 0 Output 0 0 1 0 0 0 0 0 0 1 0 0 1 100 0 0₂ 03 1 1 (a) Boolean expression(s) 0