A pump operating at 1750 rpm delivering 500 gpm against a total head of 150 ft. Changes in the piping system have increased the total head to 360 ft. At what rpm should the pump be operated to achieve this new head at the same efficiency?

A pump operating at 1750 rpm delivering 500 gpm against a total head of 150 ft. Changes in the piping system have increased the total head to 360 ft. At what rpm should the pump be operated to achieve this new head at the same efficiency?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A turbine running at 400 rpm has a specific speed of 160 rpm and head available is 41 m. If the…

A: GivenN=400rpmNS=160rpmH=41mP=200kW

Q: A pump running at 600 rpm and delivers 22.7 m³/min of water against a total head of 19.5 m. The same…

A: Given data:- Pump running speed N1=600 rpm flow rate Q1= 22.7 m³/min total head of H₁=19.5 m. New…

Q: What are the frictional losses to be considered when calculating power consumption of a pump under…

A: The following are the losses to be considered in a pump - 1. The head loss in the suction pipe of…

Q: A centrifugal pump with a 733 mm diameter impeller runs at 1948 rpm. The water enters without whirl,…

Q: Discuss with neat diagram the pump flow characteristics if pumps are used in : (i) Parallel (ii)…

A: When pumps are connected in parallel, the total discharge is equal to the sum of the flow from each…

Q: If the flowrate passing through the apparatus is increased, what will happen to the corresponding…

A: The Bernoulli's equation for kinetic, potential and pressure head is given by, Pρg+v22g+z=c…

Q: A pump is driven at 1800 RPM and delivers 12 GPM at 2000 psi. If the volumetric efficiency is 90%,…

Q: A centrifugal pump works against 10 m at 1000 rpm. varies are curved back at an angle of 30° to the…

Q: A certain hydro-power station has a head of 500m between the upper and lower reservoir . a.…

A: GivenH=500mPart aV2=?Part bQ=60 m3/s d=?Part chL=10%V2'=?d'=?

Q: A large container filled with water and uncovered for use in fighting fires in an ethylene…

Q: Problem #2 A 6AE14 pump with impeller diameter of 12.00 in will be operated at 1750 rpm with a flow…

A: Pump: Pumps are used to deliver liquid from one place to another place having a different height.…

Q: boiler feed pump water at 90 C and enthalpy of 376.92 kJ/kg. It operates against a head of 9.5 m…

A: Given: h1 = 376.92 kJ/kg H = 9.5 m eff = 0.7

Q: A swash plate piston pump has a maximum displacement volume of 40 ml/rev. The pump is driven at 1550…

A: given data; maximumdisplacement volume(Vmax)=40ml/revspeed(N)=1550rpmmechanical efficiency…

Q: Determine the recommended minimum speed (rpm) for a radial flow pump operating at 0.165 m3/s of…

Q: For pumping a liquid refrigerant with a density of 1226 kg / m3 D1 = 200 mm, D2 = 360 mm, b1 = 50…

Q: station, there is a centrifugal pump. The pump delivers a flow rate of 0.003 m3/s. The pump radius…

Q: Which of the ff are assumptions followed by the Bernoulli eq ? the pump is working at 100%…

A: Given question: Which of the following are assumptions followed by the Bernoulli equation ?…

Q: Q.21 Water is being pumped at a rate of 0.5 ft/sec from a storage tank to a certain exit point of…

A: For solution refer below images.

Q: Saturated water at 310K is being pumped from a tank to an elevated tank at the rate of 7L/s. All of…

A: Given-Data:- To-Find:- Power (W)=?

Q: e power required to drive t e pump.

A: Need to find the power required to drive the pump.

Q: What is the maximum height the higher reservoir can sit and be filled using a fixed-speed pump with…

A: Pump Power, P=114HP=1+0.25=1.25HP=687.50lb.ft/s Pump Efficiency, η=57% Volumetric flow rate,…

Q: What is the performance of pump (in %, whole number) that supplies 80 gpm of water (80°F) with…

A: Solution is attached below:

Q: A centrifugal pump is to deliver 227 m³/hr of water from a source 4 meters below the pump to a…

A: Given data: A centrifugal pump delivers 227 m3/hr of water from a source 4 meters below the pump…

Q: The 11-in Bell and Gossett pump is tobe scaled up to provide, at best efficiency, ahead of 250 ftand…

A: Given: The size of bell and Gosset pump, D = 11 in The head, h = 250 ft The flow rate, Q = 3000…

Q: The volume flow rate of water that recirculates from the blade outlet to the impeller is estimated…

Q: The pump has an er diameter of 8 cr 1750

A: The outer diameter of the pump is .The inner diameter of the pump is .The width of the blade is .The…

Q: Saturated water at 310K is being pumped from a tank to an elevated tank at the rate of 7L/s. All of…

A: Given Rate of flow of water = 7L/s 5in schedule 40 steel pipe. 2 fittings of 90o ell standard long…

Q: The volume flow rate of water that recirculates from the blade outlet to the impeller is estimated…

Q: A centrifugal pump is required to pump water to an open water tank situated 4 km away from the…

Q: A centrifugal pump works on 220 v power supply and draws 18.5 ampere by pumping water from 23 kPa at…

A: Fluid is a state of matter which deforms continuously on the application of force externally,…

Q: A pump operating at 2,000 Ibf/in? and delivering 5 gal/min requires 7 bhp to drive the input shaft.…

Q: With a centrifugal pump directly connected to a diesel engine, 148 liters of water will be sucked 5…

Q: mp is driven bya 1 the rate of 1OC e snecific

Q: the diameter of the suction pipe is 385mm. The diameter of the discharge pipe is 268mm. If…

Q: flow rate Q in liters per minute at maximum efficiency are estimated to be

A: Given data; Condition-1 Condition-2 N1=500 rpm…

Q: A pump at an elevation of 300m is pumping 0.05 m³/s of water through 2.4 km of 150-mm pipe to a…

Q: A centrifugal pump driven by a 120-kW motor rotating at 2400 rpm is used to pump 20°C water in a…

A: Solution: Given Data: P=120 kWN=2400 rpmT=20oCH=30 mη=70%h=9 m To Find: (a) Calculate Zmax? (b) If…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

A pump operating at 1750 rpm delivering 500 gpm against a total head of 150 ft. Changes in the
piping system have increased the total head to 360 ft. At what rpm should the pump be operated
to achieve this new head at the same efficiency?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Ex2-The two pumps (n=1800 rpm) each have the following characteristics: h= (100, 90, 80, 60, 40, 2O)ft and Q=(0, 110, 180, 250, 300, 340)gpm, are to be used in parallel. They must develop a head h = 35 + 20Q2 What is the flow rate with both pumps operating at 1800 rpm? Ans: 170 gpm
Determine the recommended minimum speed (rpm) for a radial flow pump operating at 0.143 m³/s of water against a head of 291 m.
A given centrifugal pump works at a flow coefficient Cf=0.65 The pump has a diameter of 3.0 cm and a the out surface 1.3 cm^2 and runs at rotation speed of 800 rpm What is the actual flow rate? give you answer in Liter/min Your Answer: Answer units
Determine the maximum total head at which a 7hp centrifugal pump can extract at a rate of 350 gpm if the pump efficiency is 50%.
What type of impeller should be selected for pumping water (60°F) at 1200 rpm for a pump head of 750 ft and discharge of 15 cfs? O Mixed-flow impeller O Laminar-flow impeller O Radial-flow impeller O Axial-flow impeller
If the pump needs to lift a water to an elevation of 20m from its centerline while the water source is 5m above pump centerline and the flow rate is 50 GPM, compute the motor horsepower needed if the pump efficiency is 85%. NEEDS COMPLETE SOLUTION, AS SOON AS POSSIBLE.
The Head -flowrate curve for a centrifugal pump is given by: HP = 28 -30Q2 Where, HP is in meter and Q is in m3/s . This pump is used to pump water for a system with the following (H-Q) curve: HS = 8 + 150Q2 Where, HS is in meter and Q is in m3/s . What is the resulting flow rate in the system if three pumps are used in series? (a) 0.56 m^3/s (b) 0.48 m^3/s (c) 0.33 m^3/s (d) 0.36 m^3/s HINT: what is the resulting Flow-rate in the system if three pumps are used in series ? Choose correct option above
Q3
None
A centrifugal pump is generating a flow rate of 16 m3/min and a lift of 70 m at a rotational speed of 1560 rpm. What is the maximum allowable suction height for this pump? However, the water temperature is 40°C.
A centrifugal pump with a 735 mm diameter impeller runs at 1979 rpm. The water enters without whirl, and a₂ = 30ª. The actual head produced by the pump is 17 m. Find the hydraulic efficiency when V₂ = 6.7. Express your answer in decimals.
Title of the book: Fluid Power, Theory and Applications, 3rd Edition, James A. Sullivan