A pump is being used to lift water from the bottom elbow, tank to the top tank in a pipe of diameter (d) at a discharge (Q). The pipe system comprises four 90" threaded elbows. The pipe entrance is sharp-edged, and the pipe exit is sudden. An Angle Valve (fully- open) is used to control the discharge in the pipeline. elbow PanpX Given the values of Q [L/s], and d [cm], calculate the power loss due to components (i.e., minor loss) in the pipe (Pminor loss) in [W]. elbow Valve elbow Givens: Q = 9.34 d = 9.296 Answers: (1) 97.587 (2) 52.043 (3) 83.932 (4) 61.849

A pump is being used to lift water from the bottom elbow, tank to the top tank in a pipe of diameter (d) at a discharge (Q). The pipe system comprises four 90" threaded elbows. The pipe entrance is sharp-edged, and the pipe exit is sudden. An Angle Valve (fully- open) is used to control the discharge in the pipeline. elbow PanpX Given the values of Q [L/s], and d [cm], calculate the power loss due to components (i.e., minor loss) in the pipe (Pminor loss) in [W]. elbow Valve elbow Givens: Q = 9.34 d = 9.296 Answers: (1) 97.587 (2) 52.043 (3) 83.932 (4) 61.849

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A Cole pitometer is set with its orifices at the center of a 40cm pipe. Determine the discharge if the deflection, z of carbon tetrachloride (s = 1.50) in the differential gauge is 325mm. Use C = 0.84 and the ratio of the mean velocity to center velocity may be assumed as 0.83. C4o cm
Situation 1: A pump draws water from reservoir A and lifts it to reservoir B as shown. The head loss from A to 1 is three times the velocity head in the 150-mm diameter pipe and the head loss from 2 to B is twenty-five times the velocity head in the 100-mm diameter pipe. The discharge in the pipe is 20 liters/second. EI. 240m B El. Om 100mm A O 150mm El. -20m 2. Find the power delivered by the pump in kW. 3. Calculate the pressure head at point 1 in meters. 4. Solve the pressure head at point 2 in meters.
Example 6 Prove that if Q, represents normal discharge at a particular depth 'y' and Q. represents the critical discharge at same depth 'y' then. dy 1-(Q/Q So dx 1-(Q/Q
2. A discharge of 8.5 L/s of oil having a sg=0.8 occurs through the venturi shown. The diameter of the pipe is 37.5 mm while that of the throat is 25 mm. The liquid in the differential gage shown contains mercury sg = 13.6 and the rest is filled with oil 37.5 mm A) Find the velocity at the throat (7.7 m/s) B) Compute for the value of h1 (0.8125 m) C) Compute for the value of h2 (0.238 m) oil mercury 25 mm h1 37.5 mm h2
Fluid Flow in Pipes 2. The flow from pipelines A to F is 300 lit/s. Using a friction factor of 0.015 for all pipelines and with the properties listed below, compute a. the discharge at B b. the discharge at E c. the discharge at D d. headloss from 1 to 5 Pipelines A TEOREY B C D F Length (m) 350 300 320 1100 550 650 Diameter (cm) 40 25 25 30 20 45
The pipe connection shown has a series parallel connection. The rate of flow in the pipe 1 is 300 liters per sec. Assuming equal values of f = 0.02 for all pipes. Compute the discharge of pipeline 2 in cu.m per sec. Compute the discharge of pipeline 3 in cu.m per sec. Compute the discharge of pipeline 4 in cu.m per sec.
20:22 CE272-8-conserv... ■■ Turk Telekom Х 3/4 5 %71 Example 5.2 A circular pipe of radius R has a perforated section of length L. The velocity distribution of flow at section (1) is given by u Umax r The discharge per unit length of the perforated section is qr. Determine: a) the average velocity Vax at section (2) b) the difference between the mass flux rate of sections (1) and (2). <] Umax Rr u(r) R
solve
Installed is a Venturi meter on a pipe 25 cm diameter in which the maximum flow is 150 li/sec and pressure of 6m of water. The throat is 12.5 cm in diameter. Compute the discharge that would be passing through the meter when the differential manometer is as shown:
What is the difference between the pressure at the two sections? * :A horizontal pipe , I P4 in diameter, taperv gradually to 8 in. in dia meter. If the flow ir 500 cu f4 of water per minute, what i the difference between the presure at the two sections? Given : Quyo ® 500 ft³/min do 8" O 445.66 psf O 417.65 psf O 455.89 psf O 420.11 psf O 432.37 psf
L11)! 111 1........ Date No. A differential manometer is connected. at two poins A and B of two pipes as Shown on the belw figure, The pipe A Contains a liquid of sp.gr= lo5 while B contains aliquid of sp.gr=0.9. The pressure. at A and B are 9.81 X l04 N/M and 1.8 X 10u N /my respectively. Density ot mercury 13.6 g/cn². Find the difference în mercury level in the diffenential mano meter. sp.gr=Dl05 3m 2.0 Sp.gr=o9
8.7