A pump can lift water at a dischargc of 0.2 m'/scc to a hcad of 30 m. The critical cavitation number (o.) for the pump is found to be 0.144. The pump is to be installed at a location where barometric pressure is 10 m of water and the vapour pressure of water is 0.3 m of water. The intake pipe friction loss is 04 m. Using the minimum value of NP SH (Net Positive Section Head), The maximum allowable elevation above the sump water surface at which the pump can be located is

A pump can lift water at a dischargc of 0.2 m'/scc to a hcad of 30 m. The critical cavitation number (o.) for the pump is found to be 0.144. The pump is to be installed at a location where barometric pressure is 10 m of water and the vapour pressure of water is 0.3 m of water. The intake pipe friction loss is 04 m. Using the minimum value of NP SH (Net Positive Section Head), The maximum allowable elevation above the sump water surface at which the pump can be located is

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The velocity of water is measured using an orifice meter (throat diameter = 0.06m) in a 0.31-m pipeline. The measured pressure drop across the orifice is 75 kPa. The Reynolds no. at the orifice is ?
Which of the ff are statements made in construction the Bernoulli eq? that the velocity at the inlet is negligible that the pressure at the inlet and outlet must be atmospheric that the flow through the orifice is in the laminar regime that the inlet and outlet are on the same level horizontally
calculate The pump efficiency if the total area equal (A=0.0032m) and (V=1.5m/s) when the total pressure pump(103.8 Pa) and the input power of the pump equal(0.85 KW) 0.92 O Full-sreen Snip 0.14 0.38 0.75 O 0.58 O
Need handwriiten solution only.
fLUID MECAHNICS The flow in the piping system shown is 10 mgd. Determine (a) the head loss from A to D and (b) the flow in pipes 2, 3, and 4. Use C = 100 for all pipes. (a) head loss : _____________________ ft of water(b)Flow in Pipe 2: _____________________ mgd Pipe 3: _____________________ mgd Pipe 4: _____________________ mgd
dy E. A Venturimeter having inlet diameter 1.8 cm and throat diameter 0.5 cm. The oil-mercury differential manometer has a reading of 5 cm. Calculate the discharge of an oil of SG=0.9.
Relation of head with co-efficient of discharge of circular orifice
For turbulent flow in pipes (smooth as well as rough) show that Vmax. = 1.33Vf + 1 V
What is the Reynolds # of the flow.? Water @ 15C is transported from a large open tank to the bottom of another open tank above. The surfaces of the two tanks are kept at 160ft apart vertically. The pipes used have an ID of 3.5 inches, and a total length of the pipe used is 150ft. In the system, there are two fully open gate valves, 6 90° elbows, and 2 standard tees. The pump used has a mechanical efficiency of 60%, and the volumetric flow rate of water is at 35 (ft^3)/s. Assume frictional losses frm sudden contraction and expansion are negligible.
ANSWER ASAP PLEASE
I need the answer as soon as possible
Water at 15°C is pumped from a reservior at a rate of 0.2428 m³/s where the local atmospheric pressure is 96.5 kPa. The total head loss in the suction pipe is 1.1 m. From the manufacturer data, the NPSH required at this operating point is 6.6. Determine the maximum height hs (meters) before cavitation can occur. Round off your answer to 3 decimal places. (10 mins) hs Vs Suction pipe Free surface of liquid Sump