a pulley system that is used to lift up the 80-kg load from the ground. Knowing that the tension developed in the cable is T = (300t/2 + 200) N when the motor is turned on. Identify the speed of the load at a time interval below 10 s. Evaluate the effect of time on the speed of the load.

Q: 1. Which type would make the solution most readable?

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: you did not derive an equation you only did an explanation thumbs down

A:

Q: In a gas turbine, the temperature of the working fluid at inlet to the compressor is 286 K and…

A:

Q: You are applying for a job in mechanical design and system company, where you have been required to…

A: Misalignment occurs when one surface or shaft is forced to deviate from its desired position.…

Q: Mention examples of problems in real life, in which some characteristic or parameter can be applied…

A: Controlling or improving a specific characteristic or parameter is crucial for achieving the desired…

Q: analyzing a process with an average processing time of 1 minute and an interarrival time of 10…

A:

Q: a) An engineer must decide how many machines of a certain type to purchase. Each machine can process…

A: Given:The fixed cost of one machine (say A), The fixed cost of other machine (say B), The variable…

Q: The output of a certain machine can be increased if it undergoes a major overhaul now and it will…

A: P = $20,000 (P/A, 15%, 5)    = $67,044 finding A when given F, Given a future sum of money, F, how…

Q: : Explain in your own words we can say iterative methods are self-correcting?

A: Numerical analysis methods are used to solve numerical problems. It can be used in various fields…

Q: Explain why efficiency can never be 100% or more on a machine

A:

Q: The key to profitable operation for project cost control is: To keep the project cost equal to…

A: Project cost: It is the total amount of fund required to complete the project. Types of project…

Q: You are given a line balancing problem with the following diagram. The processing time is above each…

A: given; number of workstation=?cycle time(t)=11line efficiency(η)=?

Q: List all the tools used in practice regarding Marking-Out Tools (name, sketches, objective and…

A: Hii, thanks for the question. We are authorized to answer three subparts at a time since you have…

Q: Write a Technical report of BRT project in your own words.

A: Bus rapid transit, also called a busway or transitway, is a bus-based public transport system…

Q: QBS company wishes to replace its current equipment that was purchased 8years ago with the newer…

A: Calculate the future worth for system A using the given data. Year Cost(C) ($) Salvage(S) ($)…

Q: The coefficient of friction is 0.14. 1) My Rube Goldberg device The stage I will assess is the…

A: Coefficient of friction→μ=0.14 Mass of the object→m=368 gm=0.368 Kg Initial height of the…

Q: Consider a milling process, where a pocket with width (X) of 400mm, Length (Y) 300mm, and depth (z)…

A: given pocket with width X=400mmlength, y=300mmdepth, z=15mmcutting tool  diameter, d=12mmcutting…

Q: A company uses various machines in the preparation of ice cream. The firm has been successful until…

A: Given:To find:Part a to part e.

Q: A company makes two kinds of door Knobs, standard and deluxe ,the making process cost the company…

A: Decision Variable  Let  SDK = Quantity of door Knobs produced i.e No of standard Door Knobs produced…

Q: grass chipper machine)

A: The grass chipper is a newly developed equipment that combines the duties of chaff cutting and…

Q: Q.1: Select the correct answer: (1) (A) Graphical method is used when most of the problems of linear…

A: 1. Graphical method is used when most problems of "linear programming" includes two decision…

Q: The Old Hickory Furniture Company manufactures chairs on the basis of the BOM shown below. At the…

A: Given:To find:a. Develop a materials plan for all the parts.b. What actions should be taken now?c.…

Q: Task 3: In the context of maintenance costing, planning, and scheduling, clarify the following: What…

A: General Categories of Potential Maintenance Costs:a. Labor Costs: This includes the salaries and…

Q: Assume yourself as a drilling fluid engineer working in a company, you asked to drill a well for…

A: Parameters that are considering while drilling a well......

Q: There are 5 steps involved when defining a project, which of the following is the last? Assign the…

A: A project is defined as a sequence of tasks that should be completed to get a certain outcome.…

Q: Five drilling machines at Al Hamriya steel is maintained by Lumina maintenance service with 2…

A: To Find:The probability that no drilling machine needs service.The probability that all drilling…

Q: OM A customer has recently tightened the specs for a part your company supplies. The specs are now…

A: Explanation: 1.Firstly identify the clause in revised specification which is very critical.  2.So if…

Q: 25) A metal sphere is dropped into a deep tank containing a viscous liquid. It experiences a…

A: When a metal sphere is dropped in viscous liquid, initially, net force acting on it is its weight…

Q: Don't Use Chat GPT Will Upvote And Give Handwritten Solution Please

A: Step 1:

Q: "Selection is done through analysis of function and properties specification" has something to do…

A:

Q: 56. List 3 (three) factors that may impact the duration of an aircraft development program. 57. What…

A: “Since you have asked multiple questions, we will solve the first question for you. If youwant any…

Q: a Buyer at Tesla and just received 18,000 tires from Michelin. The floor has discovered an issue…

A:

Q: Explain the following with appropriate examples (at least 2 examples) 1. Grubler's criterion. 2.…

A: The Grubler's criterion gives the number of degrees of freedom of a mechanism involving links and…

Q: 11 - Mark the false statement for up and down milling. a) In down milling, each chip starts out…

A: False statement for up and down milling are,

Q: a). Explain the following drilling machine parts. i) Column ii) Drill head b). Assume you are an…

A: a) COLUMN Drilling is used for forming a hole of various sizes, drilling a metal removal procedure,…

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.