A proposed fill is to be placed on the soil profile shown in Figure 3.9. A consolidation test has been performed on a sample obtained from Point A, and this test indicates the preconsoli- dation pressure at that point is 200 kPa. Determine whether the silty clay stratum is normally consolidated or overconsolidated, and compute the o solidation ratio. The proposed fill has not yet been placed. Povercon- # Hint: Determine EFFECTI E STRESS ATA water > Tevel 12m Silty Y = 19.1 kNhm :1.0m Sand (SM): Y =202 kNm 20 M Silty Clay (CL) Y=17.8 kN/m Figure 3.9 Soil profile for Example 3.3.

Please give me right solution according to the question. In a triaxial test on a saturated clay, the sample was consolidated under a cell pressure of 160 kPa. After consolidation the cell pressure was increased to 350 kPa, and the sample was then failed under undrained condition. If the shear strength parameters of the soil are c’ = 15.2 kPa, ϕ’ = 26°, B = 1, Af = 0.27, determine the pore pressure at the failure.

A given saturated clay is known to have effective strength parameters of c' = 10 kPa and = 28°. A sample of this clay was brought to failure quickly so that no dissipation of the pore water pressures %3D could occur. At failure it was known that o KPa, o = 10 KPa and = 20 kPa. %3D (a) Estimate the values of o, and oz at failure (b) Use the Mohr circle to illustrate the effective stress and total failure stress.

Find the C, and the "apparent" OCR for a superficial clay stratum that is 4m thick. The water is at the surface. A sample of the clay has a water content of 27.9%, and a specific gravity of 2.65. An oedometer test showed the following results: Voids Ratio 0.736 0.733 0.73 0.675 0.638 0.6 Vertical Effective Stress 15 28 60 230 480 930

The laboratory consolidation test is conducted on a clay sample. The following data results were obtained P1 =55 kPa P2 = 130 kPa e1= 0.95 e2= 0.80 Thickness of the sample of clay= 35mm Time for 50% consolidation = 3.0 min Tv= 0.197   a. Find the coefficient of volume compressibility b. Determine the coefficient of consolidation if a sample of clay was drained on both sides c. Compute the hydraulic conductivity of the clay

A sample of moist sand taken from the field was found to have a moisture content of 14% and a porosity of 38%. In the laboratory test that simulates field conditions, it was found that at its densest state, its void ratio is 85% and at its loosest state its void ratio is 40%. Determine the void ratio. Select one: a. 0.79 b. 0.57 c. 0.61 d. 0.42

A sample of moist sand taken from the field was found to have a moisture content of 14% and a porosity of 38%. In the laboratory test that simulates field conditions, it was found that at its densest state, its void ratio is 85% and at its loosest state its void ratio is 40%. Determine the void ratio. Select one: O a. 0.42 b. 0.61 c. 0.79 d. 0.57 It is the densification of soil by removal of air which require mechanical energy. Select one: a. solidification b. consolidation C. compression d. compaction What particular sand is ideal for field density test using sand cone method? Select one: O a. clean sand b. Ottawa sand c. Owatta sand d. white sand

Question 2 The result presented in Table Q2a were obtained from a consolidated drained (CD) triaxial test on a normally consolidated clay sample of 75mm height x 38mm diameter tested at a confining pressure of 50 kPa. Table Q2a. CD triaxial test result Axial strain (%) 1 2 5 10 15 Applied force (kN) 0.01 0.03 0.05 0.08 0.10 Page 3 of 6 (a) Draw the Mohr circle for each stress state in the sample and the total stress path (TSP) throughout the test and determine the slope of the TSP to the horizontal.

A CU triaxial test was carried out on a silty clay that was isotopically consolidated using a cell pressure of 125 kPa. The following data were obtained: Axial load (kPa) 0 5.5 11.0 24.5 28.5 35.0 50.5 85.0 105.0 120.8 Axial strain, E₁ (%) 0 0.05 0.12 0.29 0.38 0.56 1.08 2.43 4.02 9.15 Au (kPa) 0 4.0 8.6 19.1 29.3 34.8 41.0 49.7 55.8 59.0 (a) Plot the deviatoric stress vs. axial strain and excess porewater pressure vs. axial strain, respectively. (b) Determine the undrained shear strength (su). (Note: we assume that the sample reaches failure). (c) Determine the total principal stresses (0₁,03) and the effective principal stresses (0₁, 03') at the failure, respectively.

‹ample 9.1: Following results were recorded from a consolidation test on a specime turated clay, each load being maintained constant for 24 hours before the addition o ext increment.