A propeller shaft subjected to combined torsion and axial thrust is designed to resist a shear stress of 63 MPa and a compressive stress of 85 MPa (see figure). Consider only the in-plane stresses (the stresses in the ry plane). 85 MPа 63 MPa Determine the principal stresses. Round your answers to one decimal place. Give your answers in descending order. (a) ơ1 = MPa (b) o2 = MPa (C) Show the principal stresses on a sketch of a properly oriented element.

A propeller shaft subjected to combined torsion and axial thrust is designed to resist a shear stress of 63 MPa and a compressive stress of 85 MPa (see figure). Consider only the in-plane stresses (the stresses in the ry plane). 85 MPа 63 MPa Determine the principal stresses. Round your answers to one decimal place. Give your answers in descending order. (a) ơ1 = MPa (b) o2 = MPa (C) Show the principal stresses on a sketch of a properly oriented element.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The assembly shown in figure below consists of a light rigid bar AB, pinned at O, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A = 5 mm, between the lower end of the steel rod and its pin support at C. Compute the stress in the aluminum rod when the lower end of the steel rod is touch to its support. A 0.75 m Steel A = 250 mm E = 200 GPa *i* O 1.5 m Aluminum L = 2m A = 300 mm' E = 70 GPa B D
1. The column in the figure shown has a strain on its compressive edge equal to -0.003 and has a tensile strain of +0.00185 on its other edge. Detemine the nominal values of Pn and Mn that cause this strain distribution if f'c = 21 MPa, fy = 414 MPa. Draw the column interaction diagram. en 600 Pn mm 8 - 6 32mm 75 225 225 75 600
Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 240 psi in size. (a) Determine the stresses o, Oy, and the magnitude of Txyand show them on a stress element. (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16). y Answer: (a) ox- i psi Oy- i psi Txy - i psi (b) op1 = i psi Op2 i psi
A 52-kip force acts on a machine part at point A as shown below. The diagram shows the internal normal force, shear force and bending moment acting on a particular RECTANGULAR Cross section. -30in N 10in 26in F=52 kip The value of the bending moment M you would use to find the bending stress on a stress element located 2 inches up from the bottom of the rectangular cross section is closest to: 264 kip-in O a. 408 kip-in Ob. 1,464 kip-in O c. 1,608 kip-in
7. A steel rod 3 ft long with a cross-sectional area of 0.3 in.2 is stretched between two fixed points. The tensile force in the rod is 1200 lb at 40°F. Using a = 6.5 x 10°F andE=29 x 10° psi. a) Calculate the temperature at which the stress in the rod will be 10 ksi. b) Calculate the temperature at which the stress in the rod will be zero.
Wire BC has a diameter of 0.10 in. And its material has the stress-strain characteristics shown in the figure. Determine the vertical displacement of the handle D if the pull on the handle is slowly increased and reaches the magnitude of P = 655 lb. o (ksi) 40 pulg 80 70 B 50 pulg - 30 pulg € (pulg/pulg) 0.007 0.12
A steel wire (E = 200 GPa) of diameter d = 1.0 mm is bent around a pulley of radius Ro= 400 mm (see figure below). Ro a. What is the maximum stress in the wire? b. Does the stress increase or decrease if the radius of the pulley is increased?
A thin polymer plate PQR is deformed so that corner Q is displaced downward 0.9 mm to new position Q', as shown in. Determine the shear strain at Q' associated with the two edges (PQ and QR). Assume a = 150 mm, b = 216 mm, c = 180 mm, and A = 0.9 mm. a b P R C Answer: Shear strain y = Q i A X urad.
At a point in a machine component that is subjected to plane stress, the normal and shear stresses are o, = 60 MPa, o, = 110 MPa, and Txy = 28 MPa, acting in the directions shown in the figure. At this point, determine the strain components &x, y, z, and Yxy. Assume that E = 73 GPa and v=0.29 for the machine component. £x = que 11 Ox Ez = με με με μrad
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the force P (in lb) for which the tensile stress in rod AB is thrice the magnitude of the compressive stress in rod BC if Q = 20.11 lb.
Rods AB and BC have diameters of 2.9 mm and 4.6 mm, respectively. A force F = 2.4 kN is applied to the ring at B, as shown. (Figure 1) Determine the angle so that the average normal stress in each rod is equivalent. Express your answer to three significant figures. What is this stress? Express your answer to three significant figures and include appropriate units.
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. Assume'stress magnitudes of 5,-80 MPa, S - 220 MPa. Sy For the given state of stress at a point in a structural member, determine the center Cand the radius R of Mohr's circle. Answers: C- MPa, R- i MPa. Save for Later Part 3 Determine the principal stresses (api > Op2 ) for this state of stress. Answers: Opl = MPa, o,2 = MPa Save for Later Part 4 For this Mohr's circle, determine the magnitude of the central angle between: (a) pointxand the point representing the principal stress opl- (b) point x and the point representing the principal stress Op2. (a) Angle - i (b) Angle - i