A pre-drilled hole of $10 mm in a block of 40 mm thick is required to be enlarged to 0 16mm by core drilling process as shown in the figure below. The recommended cutting speed and the feed rate are 25 m/min. and 0.2 mm/rev respectively. The specific energy of block material is 4.0 W-s/mm³.Calculate the following a) Material removal rate (mm³/s) b) Power required for machining (W). c) Time required for machining. (Sec.) d) Total material removed (mm³) e) If the HSS core drill bit used obey the Taylor's tool life equation VT0.14 the bit can enlarge before it is replaced? f) Is the above drilling operation can be done on an available drill press of 500 watts power with 80% efficiency? Check and show with calculation. = 35 (m/min), how many holes

Elements Of Electromagnetics
7th Edition
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Sadiku, Matthew N. O.
ChapterMA: Math Assessment
Section: Chapter Questions
Problem 1.1MA
icon
Related questions
Question
A pre-drilled hole of 010 mm in a block of 40 mm thick is required to be enlarged to O 16mm by core drilling
process as shown in the figure below. The recommended cutting speed and the feed rate are 25 m/min. and
0.2 mm/rev respectively. The specific energy of block material is 4.0 W-s/mm³.Calculate the following
a) Material removal rate (mm³/s)
b) Power required for machining (W).
c) Time required for machining. (Sec.)
d) Total material removed (mm3)
e) If the HSS core drill bit used obey the Taylor's tool life equation VT0.14 = 35 (m/min), how many holes
the bit can enlarge before it is replaced?
f) Is the above drilling operation can be done on an available drill press of 500 watts power with 80%
efficiency? Check and show with calculation.
o16 mm
40 mm
H Fø10 mm
Core drilling
Transcribed Image Text:A pre-drilled hole of 010 mm in a block of 40 mm thick is required to be enlarged to O 16mm by core drilling process as shown in the figure below. The recommended cutting speed and the feed rate are 25 m/min. and 0.2 mm/rev respectively. The specific energy of block material is 4.0 W-s/mm³.Calculate the following a) Material removal rate (mm³/s) b) Power required for machining (W). c) Time required for machining. (Sec.) d) Total material removed (mm3) e) If the HSS core drill bit used obey the Taylor's tool life equation VT0.14 = 35 (m/min), how many holes the bit can enlarge before it is replaced? f) Is the above drilling operation can be done on an available drill press of 500 watts power with 80% efficiency? Check and show with calculation. o16 mm 40 mm H Fø10 mm Core drilling
Expert Solution
steps

Step by step

Solved in 2 steps

Blurred answer
Knowledge Booster
Machining Processes and Machine Tools
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Recommended textbooks for you
Elements Of Electromagnetics
Elements Of Electromagnetics
Mechanical Engineering
ISBN:
9780190698614
Author:
Sadiku, Matthew N. O.
Publisher:
Oxford University Press
Mechanics of Materials (10th Edition)
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:
9780134319650
Author:
Russell C. Hibbeler
Publisher:
PEARSON
Thermodynamics: An Engineering Approach
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:
9781259822674
Author:
Yunus A. Cengel Dr., Michael A. Boles
Publisher:
McGraw-Hill Education
Control Systems Engineering
Control Systems Engineering
Mechanical Engineering
ISBN:
9781118170519
Author:
Norman S. Nise
Publisher:
WILEY
Mechanics of Materials (MindTap Course List)
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:
9781337093347
Author:
Barry J. Goodno, James M. Gere
Publisher:
Cengage Learning
Engineering Mechanics: Statics
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:
9781118807330
Author:
James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:
WILEY