A power transformer is joined in star-delta. Its line voltage ratio is 66 kV/11 kV. The current ratio of CTs connected on the 11 kV side is 200/5. Find the ratio of CTs connected on 66 kV side.

Q: What are the steps for plotting points on microstation uisng offset, station, side and elevation?

A: We need to tell about steps for plotting points on microstation uisng offset, station, side and…

Q: ock diagram of Arduino car Detector and explain operating

A: The Digital OUT of the first IR Sensor is connected to Pin 11 of Arduino and the Digital OUT of the…

Q: The concept of the state of a dynamic system refer to a .maximum set of variables The root locus is…

A:

Q: List the minimum trade size Type EMT for each of the following applications. (Objective 12-1)…

A: As per Bartleby expert policy only first individual question is to be answered. So, answering only…

Q: 1.Compare Latching and Holding Current Ratio                      note::::::::: only short answer…

A: Latching current is associated with turn-on process of SCR. Holding current is associated with…

Q: 9.a. What should be done with the connector ferrule once a connector is attached to a fiber optic…

A:

Q: Fill in the blanks: Q. Expansion of LSB is

A: A combinational circuit is one in which the various gates in the circuit, such as the encoder,…

Q: What is OSHA mission?

A: -OSHA stands for Occupational Safety and Health Administration . It is for the U.S Department of…

Q: Draw the block diagram for the light pupil system using close loop system

A: The block diagram for the light pupil is drawn below:

Q: After connecting the load to an NPN sensor, the other terminal of the load will be connected to the…

A: We need to fill the blank space for given statement.

Q: Discuss any two types of signalling mode with a neat diagram.

A: two types of signaling mode with a neat diagram

Q: At what distance is the target located from a 4–20-mA ultrasonic sensor that produces 16 mA if the…

A: From the question, it is given thatUltrasonic sensor senses a current=12 mAThe range of ultra sonic…

Q: The channel _______when Id=Idss. a. does not exist b. is closed c. is narrowest d. is widest

A:

Q: Explain Base peak? Please answer at your own easy words. Answer should be to the point.

A: Base peak is definitely as the most intense (tallest) peak in the mass spectrum, due to the ion with…

Q: The ________parameters may not reflect the actual operating conditions but simply provide an…

A: For the AC analysis of BJT or MOSFET based circuits, It is important to convert it into different…

Q: Q4: Write the following compound words in the correct form as (one word, two words, or hyphenated):…

A: AirportFossil fuelCheck-in

Q: For measurement instrument, the crucial -1 static characteristic is resolution аccuracy sensitivity

A: Since there are multiple questions uploaded within the same question, therefore solving the first…

Q: Give the other names of depletion region? (At least Two)

A: At the junction of p-type semiconductor and n-type semiconductor, in which there  is neither an…

Q: Fill in the blank to supply the missing/s words to complete the sentence. Electrical that comes…

A: Mostly power station produces the electricity in AC form it is because the distribution of the…

Q: Block diagram of Arduino car speed Detector ana explains operating

A: consider the given question;

Q: There are a number of importance of measurement and instrumentation system. Identify and explain 5…

A: importance of measurement and instrumentation system: Product development: Measurement and…

Q: How

A:

Q: What are the benefits and drawbacks of SCR and IGBT? Which is the most popular, and why?

A:

Q: question: Suppose that you want to sort blocks of different heights automatically. How can this task…

A:

Q: 2. Explain over modulation.

A:

Q: Define noise in communication systems and mention the different types Note: Please do not…

A: Noise is an unwanted signal which interferes with the original message signal and corrupts the…

Q: For an N channel E MOSFET what is the value of Id when VGS(TH)=3 V and Vgs(on)=4 V and k=1.5 mA/V2…

A:

Q: In your own words and from your own understanding, avoid plagiarism or copying from the Course…

A:

Q: 3 smallest change in the quantity that will produce the observable change in the reading is called

A: This question is related to instrumentations. It is based on concept of some terms related to…

Q: Q4) Design an arithmetic logic unit (ALU) that can do the following operations (A AND B, A-B. B-A, A…

A:

Q: 5. (a) What is the full form of the word "LASER"? Explain how stimulated emission amplifies light in…

A: (a) LASER: The full form of LASER is "light amplification by stimulated emission of radiation". A…

Q: In standard architectural site plan symbols, a fire hydrant is indicated by a/an _. A. Dark -field…

A: In this question we need to choose a correct option.

Q: Complete the wiring below, such that the two sensors are connected in series and capable of…

A: Two proximity sensors, one load and one power supply is given in the question. We need to complete…

Q: Question # 1 Discuss the technical working of walkie talkie. Your main focus should be on modulation…

A: Walkie Talkie:             Walkie talkies are handheld radios that communicate wirelessly on a…

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.