A power transformer has 1000 primary turns and 100 secondary turns. The cross-sectioal area of the core is 6 sq.cm. and the maximum flux density while in operation is 10,000 gauss. Calculate turns per volt for the primary and secondary windings.

A power transformer has 1000 primary turns and 100 secondary turns. The cross-sectioal area of the core is 6 sq.cm. and the maximum flux density while in operation is 10,000 gauss. Calculate turns per volt for the primary and secondary windings.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.11MCQ: For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the...

See similar textbooks

Related questions

Q: What is a "Peclet number?" Give its significance. Additionally, calculate the overall flux using the…

A: We need to tell about peclet number .

Q: circuit breakers. A bimetallic strip is MOST associated with a. magnetic b. thermal С. oil d.…

A: Circuit breakers are used for the protection of electrical equipment and is a part of power system.

Q: Q. 1. Select [T] for true statements and [F] for false ones. A. Any given electrical machine can…

A: 1) A) False not all electrical machines convert power in either direction . B) False Motor take…

Q: b. three The allowable ampacity of a 4 AWG THHN conductor is 95 amperes. If we have four 4 AWG THHN…

Q: Create a short essay based on your own understanding and opinion about the question, “How does a dc…

Concept explainers

Winding and Constructions

Alternating Current (AC) winding is generally of the 3-phase type due to the inherent advantages of the 3-phase machine. Armature coils must be connected to the yield balance (equivalent in magnitude and 2/3 of the series phase difference of the rod) 3-phase electromotive forces (emf). The armature should be divided into step-bands to start with slots around the perimeter.In the construction of AC machines, the frame is used as an external protective shield to protect it from environmental conditions. The frame also serves as the outer perimeter, allowing the interior to be easily placed. The static state section of the devices is the stator winding attached stator.

Question

Electrical Machines 2

TRANSFORMER EQUATION
A power transformer has 1000 primary turns and 100 secondary turns. The
cross-sectioal area of the core is 6 sq.cm. and the maximum flux density while in
operation is 10,000 gauss. Calculate turns per volt for the primary and
secondary windings. *
Your answer

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Winding and Construction of the Rotor and Stator

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
With the American Standard notation, in either a Y-or-Y transformer, positive- sequen quantities on the high-voltage side shall lead their corresponding quantities on the low-voltage side by 30. (a) True (b) False
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
A transformer has primary and secondary turns of 1250 and 125 respectively. It has core cross-sectionof 36 cm2 and its rms flux density is to be limited to 1.4 T (to prevent core saturation). Whatmaximum 50 Hz voltage can be applied on the primary side and the corresponding open-circuitsecondary voltage?The core has a mean length of 150 cm and its relative permeability can be assumed to be 8000. Whatwould be the rms exciting current when the transformer’s primary winding is excited at a voltage ascalculated above? Also calculate the magnetizing susceptance as seen from primary and secondarysides.If the transformer were to be excited at 60 Hz, 1. What should be the maximum primary voltage for thecore flux density limit not to be exceeded? 2. What would be the magnetizing susceptance as seen oneach side in this case?
A single-phase transformer is required to step down the voltage from 1100 V to 400 V at 50 Hz. The [5]core has a cross-sectional area of 25 cm? and the maximum flux density is 5Wb/m?. Determine thenumber of turns of the primary and secondary windings.
Please solve the problem i want urjent
The core of a transformer operating at 50 Hz has an eddy current loss of 100 W/m3 and the corelaminations have a thickness of 0.50 mm. The core is redesigned so as to operate with the same eddycurrent loss but at a different voltage and at a frequency of 250 Hz. Assuming that at the new voltage themaximum flux density is one-third of its original value and the resistivity of the core remains unaltered,determine the necessary new thickness of the laminations. Clear and detailed solution.
a. The core of a three phase, 50 Hz,11000/550 V delta/star, 300 kVA, core-type transformer operates with a flux of 0.05 Wb.Find (i) number of H.V and L,V turns per phase, $(ii)$ e.m.f per turn (iii) full load H.V and LV turns per phase.
A 500 kVA, 6600/440 V, 50 Hz single phase core- type power transformer has maximum flux density of 1.5 Wb/m? and induced voltage per turn of 30 V. The core area required is cm2
A single-phase transformer has 480 turns on the primary and 90 turns on the secondary. The mean length of the flux path in the core is 1.8 m and the joints are equivalent to an airgap of 0.1 mm. The value of the magnetic field strength for 1.1 T in the core is 400 A/m, the corresponding core loss is 1.7 W/kg at 50 Hz and the density of the core is 7800 kg/m3. If the maximum value of the flux density is to be 1.1 T when a p.d. of 2200 V at 50 Hz is applied to the primary, calculate: a. the cross-sectional area of the core; b. the secondary voltage on no load; c. the primary current and power factor on no load
A single-phase transformer has 500 turns on the primary and 100 turns on the secondary. The mean length of the flux path in the core is 2.0 m and the joints are equivalent to an air-gap of 0.1 mm. The value of the magnetic field strength for 1.21 T in the core is 400 A/m, the corresponding core loss is 1.8 Watts/kg at 50 Hz and the density of the core is 7850 kg/m3. The cross-sectional area of the core is 0.0187 m2. If the maximum value of the flux density is to be 1.21 T when the nominal rated voltage is applied at 50Hz, calculate the magnitude of the primary current, in amperes, if a load current of 135 A is being supplied at a lagging power-factor of 0.85. Neglect the leakage impedances in the transformer windings.
Question three: A single phase, 4600/460 V, 60 Hz, transformer is connected to a 60 Hz, 4600V power supply. The maximum flux density in the core is 0.85 T. If the induced voltage per turn in 10V, determine (a) The primary turns (N1) and the secondary turns (N). (b) The cross-sectional area (A) of the core.