In a power plant, the steam from the boiler reaches the turbine at atemperature of 330 °C. The spent steam leaves the turbine at 35°C.Calculate the maximum efficiency of the turbine.

Name: In a power plant, the steam from the boiler reaches the turbine at at
Uploaded: 2022-11-30T03:40:23.000Z
Channel: Bartleby
Description: In a power plant, the steam from the boiler reaches the turbine at atemperature of 330 °C. The spent steam leaves the turbine at 35°C.Calculate the maximum efficiency of the turbine.

in a power plant,temprature of steam after turbine=35°c=(35+273)=308 Ktemprature of steam entring in…

Answered: a power plant, the steam from the…

Engineering

Mechanical Engineering

a power plant, the steam from the boiler reaches the turbine at a mperature of 330 °C. The spent steam leaves the turbine at 35°C. alculate the maximum efficiency of the turbine.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A gas turbine that operates on Brayton cycle provides a furnace with hot pressurized gas through its exhaust at 220kPa. The turbine produces only enough power as required by the compressor. The compressor has inlet conditions of 110kPa and 300K. The inlet condition of the turbine is 850oC. Determine the pressure ratio of the compressor. Draw the schematic diagram.
A water pump is used in a heating system to deliver hot water at 91 GPM and 121 ft w.c. The pump efficiency is 90%. What is the water horsepower?
A Carnot engine whose sink is at 300 K has an efficiency of 40%. By how much should the temperature of source be increased so as to increase its efficiency by 50% of original efficiency?
Determine the total turbine power output ? in the adiabatic turbine receives the water at (15000 kPa), (873 K) for mass flow rate of (100 kg/s), In the midst part (20 kg/s) is withdrawn at (2 MPa), (350° C), and the rest outlets the turbine at pressure (75 kPa), and (95 percent )quality.Neglecting the changes in kinetic energy ,
Steam is produced for an ideal turbine at a pressure of 3.0MPa. The condenser pressure is 2.0kPa. The heat added per kilogram is 2750kJ. Neglecting pump work, determine the thermal efficiency.
A boiler produces 25 kg/s of steam at 3 MPa and 600 °C, cools the condenser with seawater so that the outlet is at 45 °C, then reheats at 500 kPa up to 400 °C, then takes perform a low pressure expansion in the turbine. Determine: net power output
Superheated steam at 18 MPa, 560 °C enters the steam turbine. The pressure at the exit of the turbine is 0.06 MPa and saturated liquid water leaves the condenser at 0.06 MPa. Pressure is increased to 18 MPa again after the pump. Find: (a) Sketch the process on a T-s diagram. (b) The net work per unit of steam flow in kJ/kg. (c) Heat transfer to steam passing through the boiler, in kJ/kg.
Initial condition: P = 2 MPasaturatedProcess: AdiabaticFinal condition: P = 0.1 MPasaturatedRequired: Turbine isentropic efficiency
A Carnot engine requires 50kJ/s from the hot source. The engine produces10kW of power and the temperature of the sinks is 30°C. What is the temperature of the hot source in °C?
According to the Carnot cycle, the thermal efficiency of a working heat machine is 28%, and water vapor is used as the working fluid. Heat transfer to the working fluid occurs at 350°C, and at this time the fluid passes from a saturated liquid state to a saturated vapor state. Since 5 kg of fluid circulates per hour in the cycle, find the power of this heat machine using the entropy of evaporation.
What would be the isentropic efficiency of a turbine if the working fluid is steam and the inlet conditions are as follow T = 400 C and P = 3000 kPa. The fluid leaves the turbine at 70 kPa and 280 C. The output power of turbine is equal to 1500000 W. Select one: a. 0.86 b. 0.2 c. 0.42 d. 0.74
iii) the exit area of the nozzle. Take Cp = 1.005 kJ/kg-K and R=287 J/kg-K Q.B3. A heat engine operates between two reservoirs at 400°C and 30°C. Half the power produced by the heat engine is used to drive a Carnot heat pump that removes heat from the cold surroundings at 2°C and transfers it to a house maintained at 27°C. The heat engine is absorbing heat at a rate of 5 kJ/s. i) Draw the complete schematic of the device ii) Determine the thermal efficiency of the heat engine iii) Determine the coefficient of performance of the heat pump iv) Determine the rate of heat loss from the house. v) Determine the minimum rate of heat extraction by the heat pump, and vi) the total rate of heat rejection.