A polytropic process (n = - 1) has initial state with P = 0 KPa, V = 0 m³ and final state with P= 600 kPa. V = 0.01 m³. Find the value of work done during this process. Select one: O a. 3 k) O b. 2 kJ O c. 4 k) O d. 1 k)

A polytropic process (n = - 1) has initial state with P = 0 KPa, V = 0 m³ and final state with P= 600 kPa. V = 0.01 m³. Find the value of work done during this process. Select one: O a. 3 k) O b. 2 kJ O c. 4 k) O d. 1 k)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: An oxygen gas R = 0.2598 KJ/kg°k and k = 1.395. If 4 kg of oxygen undergo a reversible non flow…

A: Given: R = 0.2598 KJ/kg°k k = 1.395 m = 4 kg v1 = 1.2 m3 P1= 690 kpa T2 = 600°C

Q: A 10 kg mass of superheated R-134a at 1.88 MPa and 70°C is cooled at constant pressure until it…

A: Givensuperheated R-134a m=10kgP1=1.88MPaT1=70oCcooled at constant pressure ie. P2=P1=1.88MPa…

Q: A gas initially at 15 psia and 2 ft3 undergoes a process to 90 psia and 0.60 ft3, during which the…

Q: 1) Air is compressed under Constant Entropy Process from 10 Psia, 3 ft³, 90°F to 50 Psia. Find the…

Q: Air fills a 2-m-diameter balloon at 20°C and 5 kPa gage. Additional air is forced into the balloon…

A: Given: Diameter of balloon, D1=2 m Temperature, T=20°C Pressure, P =5 kPa

Q: Steam at saturation pressure of 1.75 MPa has a quality of 78%. Find the following properties: a.) v…

A: Write the given data with suitable variables: P=1.75 MPax=78 %

Q: A piston contain a mixture of water vapor (0.9 ?3 ) and liquid (0.1 ?3 ) both at 0.5MPa. The mixture…

Q: A 250 kg part falls from an airplane and hits the ground at 150km/h a) find the kinetic energy

A: Mass of part, m=250 kgSpeed of part, V=150 km/h

Q: c) A power station has an output of 2000MW and its thermal efficiency is 25%. Determine the amount…

A: Given Data Power output W=2000 MW = 2*109 w Efficiency, 25% Calorific value of coal, CV = 30 MJ/kg =…

Q: 10kg of water at 100 bar and 350°C is cooled at constant pressure in a piston cylinder system until…

A: Given m=10 kgP=100 barT=350οCv2=0.00112 m3/kg

Q: 28. 2.5 kg/min of saturated steam at 4.6 MPa expand adiabatically until its temperature is 200 deg…

A: Mass flow rate, m˙= 2.5 kg/min= 2.560 kg/s State 1: Saturated steam and P1= 4.6 MPa State 2: T1=…

Q: Two mols of a mono-atomic ideal gas is compressed adiobatiically by doing an amount of work W on it.…

Q: In a piston-cylinder system there are 2kg of water at 200°C and 0.5MPA. The water is cooled at…

A: Given:T1=200°CP1=0.5 MPaP2=P1

Q: 2. A piston-cylinder containing steam at 700 kPaa and 250 °C undergoes a constant

Q: Determine the internal energy change for carbon monoxide, in kJ/kg, as it is heated from 312° K to…

A: Given:T1=312 KT2=1456 K

Q: 30. Steam at 2.65 MPa of 60% quality, undergoes a S = c process until its pressure becomes 0.265…

Q: 1) Air is compressed under Constant Entropy Process from 10 Psia, 3 ft3, 90°F to 50 Psia. Find the…

Q: A reciprocating cylinder arrangement of 0.1 m³ volume holds 0.5 kg of water at a pressure of 0.4…

Q: of air initially at 45 decreasing with vol

Q: Q1) A fluid initially at 155.5 °C and 1 bar, is compressed reversibly and isothermally to a state…

Q: Piston-cylinder device has a pressure of 2 bars and temperature of 200 C. The fluid inside the…

A: Given- Pressure=2 bars Temperature= 200∘C The fluid is water.

Q: 4kg of air contained in a piston-cylinder apparatus at 1 bar. 40°c is compressed isothermally untill…

A: Given: Mass of air, m = 4 kg P1 = 1 bar T1 = 40°C or 313 K P2 = 7 bar Required: (a). W ( work done)…

Q: A reciprocating cylinder arrangement of 0.1 m³ volume holds 0.5 kg of water at a pressure of 0.4…

Q: 2. a.) Find the work done by a 1-kg hydrogen on a piston when this gas compresses isothermally at…

Q: A cylinder with volume V0 has enclosed air in it. Air temperature is T and pressure is p0. The air…

A: Given, Initial volume of the gas, Vo Initial temperature , T Initial pressure , Po Volume of the…

Q: 3 kilograms of steam initially at 2 MPa and 350 degrees celcius at constant temperature until the…

Q: ssure process at 1.70 omes 0.13796 m'/kg. (h) change in intern

Q: Air is compressed under Constant Entropy Process from 10 Psia, 3 ft3, 90°F to 50 Psia. Find the…

Q: 2. During an isothermal process at 88°F, the pressure on 8 Ibm of air drops from 80 psia to 5 psig.…

Q: In the Piston-cylinder Assembly, water in the form of hot steam with a mass of 1 kg at a pressure of…

A: Mass of water, m=1kg Initial water pressure, P1=500 kPa Initial water temperature, T1=500oC Water…

Q: A change of the system temperature, AT, can be: a) positive, b) negative, c) of any sign or zero.

Q: Ideal

A: Given data:m=10 lbR=40 ft lbf/lbm.R=40lbfftlbmR*1Btu778lbfft=.0514Btu/lbm.Rcp=.25 Btu/lbm.RP1=20…

Q: Consider a piston-cylinder device containing saturated water vapor. Heat is then added until the…

Q: C. If the gas absorbed 120 kJ of heat. Calcul a) The final temperature b) Change in internal energy

A: For solution refer below images.

Q: Saturated water vapor initially at a pressure of 225 kPa and volume 0.01 is contained in a piston…

A: Given data :- V=.01 m3 P1=225 kPa Vg=.7930 m3/kg

Q: Water Boundary C. The well-inbulated rigid tank having a volume of 0 25 m contains saturated water…

Q: Q2. A cylinder includes 0.5 kg water steam with 300 kPa pressure and 0.2 m³ volume at its initial…

A: Given: Mass of the steam-water mixture (m)=0.5kgPressure P1=300kPaVolume V1=0.2m3

Concept explainers

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.

Question

100%

A polytropic process (n = - 1) has initial state with P = 0 KPa, V = 0 m3 and final state with
P= 600 kPa, V = 0.01 m³. Find the value of work done during this process.
Select one:
O a. 3 k)
O b. 2 kJ
O c. 4 kJ
O d. 1 kj

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1) Air is compressed under Constant Entropy Process from 10 Psia, 3 ft3, 90°F to 50 Psia. Find the following: a) Final volume in ft3. b) Final temperature in °F. c) Work non-flow in BTU. From the problem above use all PVT values, What if the 1lbm of air is compressed under quasi-static process (n=1.27). Find the following: d) Work non-flow in BTU. e) Heat in BTU.
A rigid tank consisting of two equal parts has a pressure of 300 kPa and 6 kg of water at 30oC on one side. The other side is completely empty (vacuum) and after a certain time, the valve in between opens and the water goes to the empty side. provided. Since the temperature inside the tank remains 30oC; a)Find the volume of the tank b)Find the final pressure, work done and heat transfer.
5. "Wet steam" at 200 kPa has 40% of its mass as liquid. The water is contained in a spring-loaded piston-cylinder, with an initial volume of 3 m'. The steam is now heated until its volume is 4.535 m and its pressure is 500 kPa. Determine: a) The final temperature b) c) The work done by the steam The total heat transferred Spring d) Show the process on a P-v diagram Steam
Consider a sealed, rigid container of 10 kg of water vapor at 25°C and 80 kpa. A paddle wheelwith a power rating of 1 kW is operated within the tank for 30 minutes. During that time 7 kJ ofheat are lost to the surroundings. a.) Define the system. b.) What types of energy transfer occur? c.) What is the net energy change of the system?
1) Air is compressed under Constant Entropy Process from 10 Psia, 3 ft3, 90°F to 50 Psia. Find the following: a) Final volume in ft3. b) Final temperature in °F. c) Work non-flow in BTU. 2) From problem #1 Use all PVT values, What if the 1lbm of air is compressed under quasi-static process (n=1.27). Find the following: a) Work non-flow in BTU. b) Heat in BTU. Please answer only number 2.
A piston-cylinder assembly contains 0.35 kg of air at 500 kPa pressure and 57 °C temperature. First, the volume is brought to three times the initial volume by giving heat at constant pressure. Then at constant temperature the air is expanded up to 300 kPa. a)Show the whole event in a P-v and T-v diagram. b) Find the work and heat transitions in each process.
I need the answer as soon as possible
The temperature inside the piston-cylinder device is 400 C and the fluid is refrigerant R-134a. Can we determine its internal energy if the fluid is at saturated vapor state? A)no B)yes
Answer the number 2. Only
In a closed container whose volume does not change, a mass of 1 kg, a pressure of 1000 kPa and 400°C There is water in the form of superheated steam at temperature. All of the water in the bowl is saturated Heat is given to the environment until it turns into steam. a) Calculate the heat transfer (kj). b) Find the final temperature of the water (°C). c) By taking the boundary temperature between the container and the environment equal to the final temperature of the water, Find the amount of entropy produced during this process (kj/K). Note: The changes in kinetic and potential energies will be neglected and T (K) = 273 + °C will be taken.