A pneumatic cylinder with a 25 mm internal diameter operates at a pressure (Q4) of 0.50 MPa is used to activate a clutch that is required to transmit 10 kw at 1600 revolutions per minute. The friction interfaces of the clutch are a rigid molded non asbestos with coefficient of friction= 0.45 and pmax =1.0 MPa . The outer diameter of the clutch is initially assumed to be 150 mm and the inner diameter is assumed to be 100 mm. Determine the activation force and the number of * .friction surfaces and disks

A pneumatic cylinder with a 25 mm internal diameter operates at a pressure (Q4) of 0.50 MPa is used to activate a clutch that is required to transmit 10 kw at 1600 revolutions per minute. The friction interfaces of the clutch are a rigid molded non asbestos with coefficient of friction= 0.45 and pmax =1.0 MPa . The outer diameter of the clutch is initially assumed to be 150 mm and the inner diameter is assumed to be 100 mm. Determine the activation force and the number of * .friction surfaces and disks

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The cross section of a bearing block is shown in the figure by the shaded area. Calculate the moment of inertia of the section about its base a-a. Assume b - 11 in., h - 3 in., r-2 in, R- 4 in. R h Answer: I - i in.
An aluminum rod 20 mm in diameter and 5 m long is subjected to an axial tensile load of 50 kN compute strain if E for rod is 70x103 Mpa. O a. 5.67x10-3 O b. 2.87x10-3 O. 3.27x10-3 O d. 2.27x10-3
A= 7 1: The questions vary with the student number. Each student has to solve the questions considering his or her student ID. Use "A" as last number of your student ID. If it is zero, please take that value as 5 instead of zero. Am The W250*67 is made of A992 steel and is used as a column that has a length of A m. If the ends of the column are fixed supported, a) Determine critical load b) Can the column support the critical load without yielding? Area=8560 mm? E=200 GPa L=104*10" mm L-22.2*10 mm* Yield Strength of Steel= 345 MPa X-X
Problem-ddd: Consider FIG-ddd in the appendix. Note: The band brake is use... P = 100 N D H = 0.30 300 mm ¡30% 200 mm 100 mm 150 mm A FIGURE-ddd Problem-ddd: Consider FIG-ddd in the appendix. Note: The band brake is used to slow a rotating drum (spinning clockwise about O). a The braking process takes 5 seconds. a The static coefficient of friction between the belt and the drum is 0.50. Calculate: See Blackboard Your analysis is at 2 seconds into the 5 seconds braking process. Problem-ddd The magnitude of the x-component of the reaction force at 'A' is The magnitude of the y-component of the reaction force at 'B' is The magnitude of the "low tension" in the band brake is The magnitude of the angle of belt contact with the drum is N. N. N. radians.
A supersonic diffuser cruising at M. = 2.8, where the atmospheric air pressure is P = 10 kPa and the temperature is T=0°C. A normal shock occurs at the exit of the diffuser (see figure below). The diffuser has an area ratio A./A₁ = 4. Determine (a) M₁, P₁, PT1, and T₁. (b) M2, P2, PT2, and T2. (c) Velocity at the inlet, Vi. (d) Velocity at the exit, V₂ (downstream of the shock). Ma P To
A= 7 1: The questions vary with the student number. Each student has to solve the questions considering his or her student ID. Use "A" as last number of your student ID. If it is zero, please take that value as 5 instead of zero. Am The W250*67 is made of A992 steel and is used as a column that has a length of A m. If the ends of the column are fixed supported, a) Determine critical load b) Can the column support the critical load without yielding? Area=8560 mm L=104*10 mm =22.2*10 mm* Yield Strength of Steel= 345 MPa E=200 GPa
Question 7 (a) - Drive the equilibrium equation of motion for 2 DOF system equipped with base isolation as showed in following figure. (b) - Drive base isolation natural frequency. kb mb Xb K₁ www m₁ X₁ K₂ ww m₂ X2
Determine the (a) product moment of inertia at steel cross-sectional area with respect to centroidal axes and then (b) calculate the minor and major principal values of moment of inertia with respect to centroidal axes. (Imin Imax). 250 mm mm TUUR OS 350 mm 50 mm 150 mm
A gas under pressure of 12.868 bar abs at 40°C. a. compute the pressure in kpa b. compute the gage pressure c. compute the gas R if it has a unit weight of 362n/m³ (OUR SUBJECT IS FLUID MECHANIC)
E pe Vi5 For the frame shown below, the initial displacement is 25 mm and the initial velocity is 13 mm/s. Damping is 10% of critical. Cross-sectional dimension of each column is 250 mm x 300 mm and elastic modulus is 22.8 GPa. Determine (a) () (c) the natural frequency (rad/s) the amplitude the expression for the displacement 500 kN 3 m 5m 5 m
The 10-lb box A is released from rest and slides down along the smooth ramp and onto the surface of a cart as shown in (Figure 1). Show Transcribed Text 10 ft G B G Ć 4 ft
Assuming smooth contact surfaces, determine the reactions A, B, C and D on the cylinders as shown in the fig. Show your solutions in two ways. W 200 lb We400 lb to 5.6'