A PMMC instrument with FSD = 50µA and Rm =2.2k2 is to be employed as an ac voltmeter with FSD=220V (rms). Silicon diodes are used in the bridge rectifier circuit of figure. Calculate the multiplier resistance value required. 4 D. Mutiplier PMMC instrument *D.

Q: (a) a new rest chair for Proton Research and Development Centre are designing (DAC) as shown in…

A: The given question is based on a 4-bit Digital to Analogue Converter (DAC) realized using the…

Q: Enumerate at least 10 applications of instrumentation in ease operation

A:

Q: 6. Compare and contrast the Closed and Open loop Control System

A: In the given questions we need to discuss about the close loop system and open loop system.

Q: When using Oscilloscope Differential Probes Select one: a. A differential probe uses a built in…

A: When using Oscilloscope Differential Probes :

Q: 9. In pneumatic system have we two types of pressures 10. In Electronic pressure sensors the…

A: Pneumatic system deals with different kinds of pressure study. We are mainly using two kinds of…

Q: A relay has a resistance of 350 ohms and an inductance of 0.8 henry. V volts is suddenly impressed…

A:

Q: is a typical configuration of an exothermic chemical reaction occurring in a Continuous Stirred Tank…

A: Introduction: The jacketed stirred reactor is a self regulating processes. That is, the measured…

Q: SCADA in electrical engineering. Provide its importance to the field.

A:

Q: 5- What is the mathematical form of electrical transducer efficiency?

A: Transducer:-  A transducer is an electrical equipment used for monitoring and data transfer that…

Q: A gas stove system has to be in automation form to enhance easy regulation and control. Make a…

A: Automated gas stove block diagram of close loop system:

Q: What are the Suitable sensors for design and appropriate actuators for design

A: We have to explain the Suitable sensors for design and appropriate actuators for design.

Q: Write a report on the piezoelectric sensors used in various industries. Discuss the working…

A: Sensors: Sensors are the devices or systems which detect the change and responds in the form of an…

Q: What is a DAC? Mention its types. Explain any one type in detail.

A:

Q: 13. Name two circuits that can be used to create clock generators in ASICS. a. b.

A: Two circuits which can be used to generate clock in ASIC are frequency synthesizer and PLL and…

Q: .The transducer can be classified into. . and .transducer ..Transducers which are used to measure…

A: 1. Basically there are two types  1. Active transducer and  2. Passive transducer      2. Force…

Q: Choose the correct statement for Dual converter (a) Rectifier Il produces 2 nd Quadrant parameters…

A:

Q: 2. The voltage sensitivity of the full bridge differential circuit is ( the single arm bridge. A. 2…

A: The question is about sensitivity of full bridge.

Q: 3. What are the limitations of Multivibrator? Briefly discuss how multivibrator can be used as a…

A:

Q: >) An 8-bit microcontroller is used for a temperature measurement setup which the sensor is placed 2…

A: Given : ADC reference voltage : 5 V Sensor senses up to: 120 degrees Celsius Sensor output :2 mV/c…

Q: QUESTION 6 A component which converts electrical energy into mechanical rotation is O A.…

A: Choose the correct option of given questions.

Q: A Explain the definition and theoretical background of potentiometers. B. Discuss the difference…

A: Electrical and electronics measurement instruments are very important for determining the various…

Q: Part C-We have different Micro-controllers which can be operated through Transistors but the major…

A: A microcontroller is basically a small computer on a metal oxide semiconductor integrated circuit…

Q: PLEASE INCLUDE A DETAILED STEPS What are the steps in designing combinational circuits?

A: This question is related to digital circuits.

Q: xplain the following: a) Elaborate why the method of inverted R-2R ladder is preferred in DAC as…

A: A) The method of inverted R-2R ladder is preferred in DAC because: Easier to build precisely as…

Q: (a) Aided with drawing state the types of control systems defining the main function of the…

A: a) A Transducer is a device that converts one form of energy into another by the principle of…

Q: (a) Draw the circuit diagrams describing the operation of one and two direction resistive position…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: What is biomedical Instrumentation explain with examples

A: Biomedical Instruments  Bio-Medical Instruments is the application of knowledge and technology to…

Q: 1) PCB layout of the switch gives Actuator options dimensions and placements Bushing options…

A: The real world demands the analysis and design of complex systems. It is possible with the clear…

Q: 1_ What do you consider to be the main difference between a hydraulic actuator and a hydraulic…

A: Hydraulic pressure sensors give good repeatability and precise findings over long periods of time.…

Q: Introduction explaining the importance of the measurement process

A: Importance of measurement process in electrical  and electronics systems is shown below using…

Q: ISCUSSION: Give to applications for the multiplexer.

A: There are following multiplexer application are: 1.  We can take output as per according…

Q: Q1. The set of independent of voltages are recoded as :50.8, 50.5, 50.2, 50.1, 50.3,50.6. Calculate:…

A: We are authorized to answer only 1 question and only 3 subparts at a time since you have not…

Q: How does an electrical engineer practice management? Give examples of management being practice by…

A: Management is the one of the most important non technical aspect for an electrical engineering…

Q: What is the principle of spatial and temporal locality of reference?

A: Registers are sequential circuit used to store binary information. Semiconductor memory are use for…

Q: Q1.Explain temperature compensation of strain gauge in detail?

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: www 6 +5)*100] to 6 +10)*400] Newtons. Design required amplifier circuit(s) for scaing the force…

A:

Q: What are some of the benefits and drawbacks of considering system engineering to be a distinct…

A: Benefits of considering system engineering as a distinct profession from electrical engineering and…

Q: Explain the following NILM performance indices 1. Precision 2. Accuracy 3. Recall

A: Precision: Precision can be calculated by the ratio of the True Positive with the sum of the true…

Q: Discuss the role of power electronics and applications? D

A:

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.