A playground merry-go-round of radius R 2.03 m has a moment of inertia of I 29.1 kg child hops onto the merry-go-round and manages to sit down on its edge. What is the new angular speed (in revolutions per minute) of the merry-go-round? Do not enter units. 248 kg m and is rotating at 10.2 revolutions/min about a frictionless vertical axle. Facing the axle, a

A playground merry-go-round of radius R 2.03 m has a moment of inertia of I 29.1 kg child hops onto the merry-go-round and manages to sit down on its edge. What is the new angular speed (in revolutions per minute) of the merry-go-round? Do not enter units. 248 kg m and is rotating at 10.2 revolutions/min about a frictionless vertical axle. Facing the axle, a

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A playground ride consists of a disk of mass M = 38 kg and radius R = 1.5 m mounted on a low-friction axle (see figure below). A child of mass m = 24 kg runs at speed v = 2.5 m/s on a line tangential to the disk and jumps onto the outer edge of the disk. R m M
Plz use g = 9.8 m/s2 to find if needed
A 330 N sphere 0.20 m in radius rolls, without slipping 6.0 m down a ramp that is inclined at 37 degrees with the horizontal. What is the angular speed of the sphere at the bottom of the hill if it starts from rest? Rad/s
A top has a moment of inertia of 4.8 kg-m2. The top is spinning at 35 rpm. How much rotational kinetic energy (in joules) does the top have?
Your grandmother enjoys creating pottery as a hobby. She uses a potter's wheel, which is a stone disk of radius R = 0.430 m and mass M = 100 kg. In operation, the wheel rotates at 45.0 rev/min. While the wheel is spinning, your grandmother works clay at the center of the wheel with her hands into a pot-shaped object with circular symmetry. When the correct shape is reached, she wants to stop the wheel in as short a time interval as possible, so that the shape of the pot is not further distorted by the rotation. She pushes continuously with a wet rag as hard as she can radially inward on the edge of the wheel and the wheel stops in 6.00 s. (a) You would like to build a brake to stop the wheel in a shorter time interval, but you must determine the coefficient of friction between the rag and the wheel in order to design a better system. You determine that the maximum pressing force your grandmother can sustain for 6.00 s is 60.0 N. HK (b) What If? If your grandmother instead chooses to…
A cable lifting an elevator (600-kg) is wrapped around a 1.0-m diameter cylinder (20-kg) that is turned by the elevator's motor. The elevator is moving upward at a speed of 2.0-m/s then slows to a stop. (Note: I(cylinder)= ½ M R?) a. What is the angular acceleration (a) of the cylinder? b. What are the initial and final angular velocities (w) of the rotor. c. What angle (Dq) does the cylinder cover while stopping? d. How long does it take to stop the elevator?
A merry-go-round is a common piece of playground equipment. A 3.0-mm-diameter merry-go-round, which can be modeled as a disk with a mass of 260 kgkg , is spinning at 17 rpmrpm. John runs tangent to the merry-go-round at 5.4 m/sm/s, in the same direction that it is turning, and jumps onto the outer edge. John's mass is 30 kgkg. Part A What is the merry-go-round's angular velocity, in rpmrpm, after John jumps on? Express your answer in revolutions per minute.
page A person 1.56 m tall swings their leg from the hip at 1.51 radians/s. Calculate the linear tangential velocity (v) at their knee to 2 decimal places. Answer. re to search 561 R T 6 B N U 8 O Pa Next page d Construction on A20...
Consider the 13.0 kg motorcycle wheel shown in the figure. Assume it to be approximately an annular ring with an inner radius of R1 = 0.280 m and an outer radius of R2 = 0.420 m. The motorcycle is on its center stand, so that the wheel can spin freely. a. If the drive chain exerts a force of 1800 N at a radius of 5.00 cm, what is the angular acceleration (in rad/s2) of the wheel? b. What is the tangential acceleration (in m/s2) of a point on the outer edge of the tire? c. How long (in s), starting from rest, does it take to reach an angular velocity of 80.0 rad/s?
A professor sits on a rotating stool that is spinning at 10.0 rpm while she holds a heavy weight in each of her hands. Her outstretched hands are 0.745 m from the axis of rotation, which passes through her head into the center of the stool. When she symmetrically pulls the weights in closer to her body, her angular speed increases to 40.5 rpm. Neglecting the mass of the professor, how far are the weights from the rotational axis after she pulls her arms in? distance: about us careers privacy policy terms of use contact us help tv W MacBook Air 8828
A playground ride consists of a disk of mass M = 38 kg and radius R = 1.5 m mounted on a low-friction axle (see figure below). A child of mass m = 24 kg runs at speed v = 2.5 m/s on a line tangential to the disk and jumps onto the outer edge of the disk. R m M
A horizontal platform in the shape of a circular disk rotates on a frictionless bearing about a vertical axle through the center of the disk. The platform has a radius of 2.36 m and a rotational inertia of 218 kg-m2 about the axis of rotation. A 72.6 kg student walks slowly from the rim of the platform toward the center. If the angular speed of the system is 2.07 rad/s when the student starts at the rim, what is the angular speed when she is 0.433 m from the center? Number i Units