A plane blow leak velocity component u = V: T₁' y T₂ and w = 0 along x, y and z direction respectively where T₁(# 0), T₂(# 0) are constants having dimension of time. The given blow is incompressible if

Q: 5.1 The recommended scales for use on technical drawings are specified in the following table.…

A: To find: Choose the suitable code for the given scales for use on technical drawings.

Q: Determine external as well as total indeterminacy

A: Given data : Number of External support reaction (R)=2+2=4Number of member (m)=6Number  of joint…

Q: Determine the centroid of the shaded area shown, which is bounded bythe X axis and the parabola y? =…

A:

Q: What do you mean by the slice action and how many slice operated dimensions are used?

A: #1What do you meant by the slice action?? A slice operation is defined as the particular filtration…

Q: 32. What is the area of an octagon inscribed in a circle having an area of 224 sq.m?

A:

Q: Find the shortest distance from point B to line AC

A:

Q: 16m 8m 60° 126m 120m 20m 64m 16m

A:

Q: 10 25k 10'

A: The below cantilever beam is given;

Q: The

A: The construction schedule normally contains sufficient detail to schedule the day to day work on a…

Q: ETERMINE THE LOCATION OF CENTROIDAL X AND Y. NOTE: UNITS ARE IN INCHES.

A:

Q: 3. Name any two-pattern material.

A: Introduction- There are several types of material found in nature. Some materials form certain…

Q: Name any four shape that you can identify from the sketch

A: Any sketch such as still life, landscape etc. is prepared with the helps of basics shapes. These…

Q: Determine degree of total indeterminacy

A: Given data : The given structure is truss structure . It is pin connected carrying tension or…

Q: * To draw an arc angle between two intersecting lines Fillet O Block O Trim Chamfer O If we want to…

A:

Q: 1) Determine the area of the shape below. -130.0- 100.0 -160.0-

A: The above figure is the trapezoid  The area of the trapezoid = sum of the parallel…

Q: A drone is flying in the air at some altitude. The drone is equipped with piezometer that indicates…

A:

Q: You are appointed as an officer of Occupational Safety to investigate the incident happened during…

A: Officer of Occupational Safety is responsible for 1) Enforcing safety policies, 2) Conducting audits…

Q: List some benefits of using hand-level instruments.

A: A hand level instrument is a device which is used  for rough levelling.  It is mainly used for small…

Q: For the given structures, determine the degree of indeterminacy. 1. ♫

A: This question is related to the Structure analysis

Q: Determine the centroidal coordinates (x, y,z) of the volume.

A: Question is based on the section . Dimension of section are given in the question . Centroidal…

Q: Describe Mohr’s Circle.

A: Mohr’s circle is defined as a two-dimensional graph which represents stresses at a point.

Q: What is used to mark the tape lengths?

A: In surveying, tapes are used to measure distances that are level, vertical, or sloping. Tapes are…

Q: express each measurement in feet.108 inches

A:

Q: Determine external indeterminacy

A: Given data : Number of external support reaction (R)=2+1+1+2=6

Q: -0129 -077 R26

A:

Q: Dipper is another word for bucket. ) True False

A: A word or phrase that is exactly the same as another word or phrase in the same language. for…

Q: 150 25 40 185 25 75 50

A: To draw the front, top and side view of the given object. Given 3d object:

Q: Explain the Importance of Auto CAD.

A: INTRODUCTION: AutoCAD is used by architects and drafters to create plans for buildings, bridges, and…

Q: Beginning ^ 2 3 4 LO 5 CO 9 8 7 3 10 10 11 12. 13 5 14 15 Identify the full name and abbreviation of…

A: To Determine: Full name and abbreviation of 8 10 15

Q: Construct a diagonal scale and show on it a distance of 1.12 inche

A: Diagonal scale is an engineering measuring instrument that is combined with a set of parallel…

Q: Please explain step 4 and 5

A: Grade: g1 =3%  g2 =-4% Station of intersection = 3+400 Elevation of intersection = 7600 m Station…

Q: 12 13 12 13 14 10 Which tools that can be used to :4 draw the following shape in .AutoCAD R5 R10 R12…

A: To draw the given shape we will require the following command necessarily :- Dimension, line or…

Q: geven that 1-front view 2-top view find the 1-side view 2-front section

A: In engineering drawing, a different type of projection is there the isometric projection is the…

Q: What are the possible Geometric Design? Make a table Containing the Geometric Design and Design…

A: Geometric design is the process of determining the layout and dimensions of visible features of a…

Coordinate Geometry of Survey

Coordinate geometry (COGO) is a method of inserting surveying or engineering data into geographic information system (GIS), computer-aided design (CAD), or mapping software. These data can be collected on the proposed construction site using standard surveying techniques and instrumentation or may be taken from existing maps, engineering plans, drawings, or records. Data gathered on the site includes coordinates of points, bearings, and distances between points. The data are noticed and noted through conventional surveying procedures, like a traverse or layout measurement series and it can be either digital or non-digital. The maps and plans are inclusive of boundaries, divisions, and other components, and these features are shown with coordinate values, the lengths, offset distance, and bearings between them.