A pivot in a linkage has a pin in the figure whose dimension a + ta is to be established. The thickness of the link clevis is 37.5 ± 0.125 mm. The designer has concluded that a gap of between 0.1 and 1.25 mm will satisfactorily sustain the function of the linkage pivot. Determine the dimension a and its tolerance. Clevis Pin Snap ring - 1.05±0.05

Q: he values of stress amplitude and stress ratio

A: Given ; From the given figure; Fluctuating fatigue load Find the stress amplitude and stress ratio ?…

Q: The maximum shear stress in a solid round bar is Tma- 16T/n(d). The bar is subjected to a torque of…

A: AS PER GUIDELINES, ONLY ONE QUESTION CAN BE SOLVED AT A TIME. FOR SOLUTION OF OTHER QUESTIONS,…

Q: Calculate the range for the stress of the load measures 100 lbs. and the load cell used has an error…

A: Calculated the range of stress of the load .

Q: Using the sample set of readings provided for Experiment 1 and taking the Young's Modulus of steel…

A: i hope its helpfull.thank you.

Q: Problems 145 For the data below, find the slope and intercept relating two hardness scales for…

A:

Q: On the part below, with only the limits of size specified, what coaxiality tolerance is implied…

A: In this problem, it is asking about the co-axially tolerance between the two diameters.

Q: Using the sample set of readings provided for Experiment 1 and taking the Young's Modulus of steel…

A: i hope its helpfull.thank you.

Q: 10 units of bulb were tested where the normal lifespan is 100 hours 3 units of bulb failed at 10…

A: Failure rate per hr.

Q: Hole-MMC_ LMC_ LMC Shaft-MMC_ LMC_

A:

Q: A part is to be chosen from a sample of 1000 pieces which have a mean tensile strength of 80kPa and…

A: Write the given data. Smax=85 kPaSmean=80 kPaSD=8.5 kPaN=1000

Q: Determine tolerance value and limit dimension of the rod which a diameter is ∅25 mm, according to…

A:

Q: Using the sample set of readings provided for Experiment 1 and taking the Young's Modulus of steel…

A: i hope its helpfull.thank you.

Q: 3-132 Steel 0 1.002/1.003 Steel 1.001/1.002 2.00

A:

Q: The notch sensitivity "q" which is expressed in terms of fatigue stress concentration factor Kf and…

A: Notch sensitivity is the ratio of increase in fatigue stress over nominal stress to the increase in…

Q: Determine the young’s modulus value of each material testing, and indicate which material is the…

A:

Q: 4. The drawing below shows a pin with coaxial features. If the modifier M were removed from the…

A: Feature control frame Geometric symbol – this is where your geometric control is specified. Diameter…

Q: (a) Write down the slip gauge selection for 163.94 mm using the standard BM1-447-11 slip gauge set…

A: Gauge blocks are a system for producing precision lengths. The individual gauge block is a metal or…

Q: Fatigue test are carried out

A: Fatigue test or Rotating beam is carried to know the fatigue stress, in which the beam is rotating…

Q: Title The dimension of the mating nut is selected according to which parameter of the bolt? (a) d…

A:

Q: What is the width of the groove on the bolt?

A: Given :- Bolt drawing Find :-  Width of the groove on the drawing = ?

Q: An engineer is designing a cylindrical steel pin that must fit into a bronze bushing for a…

A: Limits, Fits, and Tolerances  deal with the dimensional accuracy and operational interplay of mating…

Q: What are the geometry features in the picture below? Indicate main geometry and tolerances

A: Geometry Features which mentioned in the Drawing are as below:

Q: Problem 6-5: The mass of a test specimen of metal alloy is measured to be m = 674.4 g. The procedure…

A: Given:the mass of the metal is  the standard uncertainty mass is the volume of the specimen is  the…

Q: Since the measured values and measurement errors in an inclined plane test to determine the friction…

A:

Q: On the left end of this object, the thread note indicates 10UNC. What is the pitch for this thread?

A: The objective of the question is to determine the pitch of the thread indicated as 10UNC on the…

Q: 1. A full journal bearing of 150 mm diameter supports a load of 40 kN. The speed of the journal is…

A:

Q: A suitable factor of safety to apply when selecting the cable for a factory hoist is: 05 O1.2 0.2…

A: Since you have posted multiple questions, we will provide the solutiononly to the first question as…

Q: Determine the coordinates of the mass center of the body which is constructed of three pieces of…

A: Given question: Determine the coordinates of the mass center of the body which is constructed of…

Basics of Mechanical Engineering Design

The word mechanical engineering design consists of two words, mechanical engineering, and engineering design. Mechanical engineering deals with the design and analysis of mechanical systems and components using the laws and principles of mechanics and physics. On the other hand, engineering design deals with determining the dimensions of the components or members under the action of external influences such as loads to make it fail-safe. Engineering also deals with determining the maximum and safe limit of loads and stresses that can be exerted on a body without causing the component to fail. In the domain of mechanical engineering, design is restricted to determining the permissible safe dimensions and loads that can be applied to the component without causing it to undergo fractures or deformations. Mechanical engineers are primarily in charge of the design and analysis of the mechanical components of a system under static and dynamic conditions.