A piston/cylinder has a water volume separated in VA = 0.3 m³ and VB = 0.4 m by a stiff membrane.The initial state in A is 1000 kPa, x = 0.8 and in B it is 1500 kPa and 250°C. Now the membraneruptures and the water comes to a uniform state at 200°C. What is the final pressure? Find the work andthe heat transfer in the process.PompcbA:H2OB:H20

Given Area A VA= 0.3 m3 PA= 1000 kPa x = 0.8 Area B VB= 0.4 m3 PB= 1500 kPa T=250oC To find Final…

Answered: A piston/cylinder has a water volume…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An insulated chamber containing 2 L of saturated liquid water at 300 kPa constant pressure. There is a piston-cylinder assembly. One with an electric heater inside the cylinder There is a mixer. Then the water is mixed by the mixer for a while. s mixed, as well as connected to 220 volt electrici supply and 8 A current through neated by the passing heater. This state change at constant pressure 500 kJ of work is done by the mixer. Meanwhile, iquid 90 percent by mass evaporates. a) Plot the state change on T-v and P-v diagrams, paying attention to saturation lines. D) Calculate the operating time of the electric heate
0.75kg of air has a pressure of 3bar and a temperature of 125oC , After it has received 900kj of heat at constant volume, find the final temperature and pressureIf the air then expands adiabatically doing 915kj of work,by how much is its internal energy changed during the expansion(b) is the value lower or higher before the heating process
A piston cylinder has 2.2kg of air at 300 K and 150 kPa. It is now heated up in a two step process. First constant volume to 1000 K (state 2) then followed by a constant pressure process to 1500 K, state 3. Find the final volume and final pressure. (R of air = 0.287 KJ/kg K)
Container is filled with water. The total volume is 5 m^3. 1% of the volume is saturated liquid and 99% of the volume is saturated steam where the pressure is 0.1 MPa within the container. Heat is transported to the container until all the water turns into saturated steam. Find how much heat isrequired for the process to occur.
A piston cylinder has 6 kg of air at 300 K and 150 kPa. It is now heated up in a two step process. First constant volume to 1000 K (state 2) then followed by a constant pressure process to 1500 K, state 3. Find the final volume and final pressure. (R of air = 0.287 KJ/kg K)
A piston/cylinder system with a radius of 1m is filled with 0.75kg water at 50˚C and has an initial piston height of 2m (state 1). Heat was transferred to the system such that the water at state 2 became saturated vapor. Afterward, the piston is locked, and the system is heated to 165˚C (state 3).Given the data above, calculate the work, heat transfer, and height of the piston, and create a p-v diagram for the entirety of the process.
Initial condition: T = 360Ch = 1860.8 KJ/kg Process: IsometricFinal condition: saturatedRequired: Final pressure
Consider a balloon contains initially 40 liter of Helium at 105 kPa and 20 oC, The balloonis connected to a supply line of helium through a valve that is opened allowing helium tofurther fill the balloon to 150 kPa such that pressure in the balloon is expressed as: P =750 V0.5– 45, Where P is in kPa and V is m3. Considering Helium as ideal gas:a- Find the mass of Helium entered the balloon if the process is isothermal.b- Find the work done during the process.
3.56 Refrigerant-12 in a piston/cylinder arrangement is initially at 50° C, x = 1. It is then expanded in a process so that P = Cv to a pressure of 100 kPa. Find the final temperature and specific volume.
4.9 A piston/cylinder contains 50 kg of water at 200 kPa with a volume of 0.1 m³. Stops in the cylinder restrict the enclosed volume to 0.5 m³, similar to the setup in Problem 4.7. The water is now heated to 200°C. Find the final pressure, volume, and work done by the water. H₂O FIGURE P4.9

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS