A piston/cylinder assembly contains 2 kg of liquid water at 20°C and 300 kPa, as shown in Fig. P3.33. There is a linear spring mounted on the piston such that when the water is heated, the pressure reaches 3 MPa with a volume of 0.1 m³. a. Find the final temperature. b. Plot the process in a P-v diagram. c. Find the work in the process. Po H20 Figure P3.33

A piston/cylinder assembly contains 2 kg of liquid water at 20°C and 300 kPa, as shown in Fig. P3.33. There is a linear spring mounted on the piston such that when the water is heated, the pressure reaches 3 MPa with a volume of 0.1 m³. a. Find the final temperature. b. Plot the process in a P-v diagram. c. Find the work in the process. Po H20 Figure P3.33

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

One kilogram of ideal gas(k=1.7, MW=10kg/kmol) underwent a polytropic process from P1=1MPa, T1=300C and P2=200MPa, T2=400C. Find the work done and heat transfer of gas.
Q3/ A cylinder fitted with a movable piston contains water at 3 MPa, 50% quality, at which point the volume is 20 L. The water now expands to 1.2 MPa as a result of receiving 600 kJ of heat from a large source at 300°C. It is claimed that the water does 124 kJ of work during this process. Is this possible? i
The initial state (state 1 ) of a system containing 1.0 kg of water is 110 Co and 0.4 m3 volume . The water is now heated to state 2 through the path shown at which the final pressure is 500 kpa and temperature of 200 Co. Find the work and heat transfer in this process
A constant-pressure piston cylinder apparatus contains 0.5 kg of saturated water at 211 °C and 25% quality. The system is then cooled to that the water occupies half of the original volume. Find the work involved in the process
A piston cylinder has 6 kg of air at 300 K and 150 kPa. It is now heated up in a two step process. First constant volume to 1000 K (state 2) then followed by a constant pressure process to 1500 K, state 3. Find the final volume and final pressure. (R of air = 0.287 KJ/kg K)
3.56 Refrigerant-12 in a piston/cylinder arrangement is initially at 50° C, x = 1. It is then expanded in a process so that P = Cv to a pressure of 100 kPa. Find the final temperature and specific volume.
4.9 A piston/cylinder contains 50 kg of water at 200 kPa with a volume of 0.1 m³. Stops in the cylinder restrict the enclosed volume to 0.5 m³, similar to the setup in Problem 4.7. The water is now heated to 200°C. Find the final pressure, volume, and work done by the water. H₂O FIGURE P4.9
An ideal gas initially occupying 0.020 m3 at 1.0 MPa is quasistatically expanded inside a piston-cylinder device at a constant pressure until its volume doubles. Next the expansion is continued at constant volume till the pressure reaches half of the initial pressure. Finally it is brought back to the initial state in a polytropic process with exponent n=1.6 a) Draw the processes on a P-v diagram and calculate the total work. b) Calculate the total heat transfered, what is the difference between the initial and final temperature?
Water with a quality of 53,5% and pressure of 200 kPa is inside a rigid tank. The tank is heated by an electric heater rated as 120W for 8 minutes until the temperature reaches 250C. find quality at final state if any ?
Read the question carefully and give me right solution according to the question
A reciprocating compressor compresses air 1/8 th times of its initial volume. If the pressure of air beforecompression is 5 bar and volume of air after compression is .016m 3 , when the law followed is pv 1.6 =constant. Calculate the work done and draw the process on PV diagram.