A piston-cylinder device initially contains 1.5 kg steam at 5 MPa and 507°C. Now the steam loses heat to the surroundings and the piston moves down, hitting a set of stops at which point the cylinder contains saturated liquid water. The cooling continues until the cylinder contains water at 187°C. a. Sketch both p-v and T-v diagrams,Then determine b. The actual specific volume at starting state using the compressibility chart, and the percentage error % c. The final pressure (bar) and the quality (if mixture), Tho

A piston-cylinder device initially contains 1.5 kg steam at 5 MPa and 507°C. Now the steam loses heat to the surroundings and the piston moves down, hitting a set of stops at which point the cylinder contains saturated liquid water. The cooling continues until the cylinder contains water at 187°C. a. Sketch both p-v and T-v diagrams,Then determine b. The actual specific volume at starting state using the compressibility chart, and the percentage error % c. The final pressure (bar) and the quality (if mixture), Tho

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A piston-cylinder device contains an ideal gas of nitrogen. At the initial state, the volume is V1= 1.00 m3, the pressure is p1= 400.00 kPa, the temperature is T1= 300.00 K. An electric heater within the device is turned on for a time of Δt = 5.00 min. The current is I = 3.00 A, and the source voltage is V = 120.00 V. During the heating process, the gas expands, and a heat loss of Qout = 2.80 kJ occurs. The gas constant is R = 0.297 kPa·m3/(kg·K), and the room temperature specific heat at constant pressure is cp =1.039 kJ/(kg·K). Calculate the mass of the gas, m__________ (kg)
b) As shown in Figure A2-b, an insulated rigid container holds 1.4 kg of saturated water and air. At the initial state, the temperature of the saturated water is 210°C and 75% of the volume is occupied by air and the rest by the saturated liquid. An electric heater inside the container heats the water and converts to saturated vapor after 0.333 hours. Air Water 1.4 kg, 210°C Figure A2-b Determine the volume of the container in m³. Determine the temperature of the saturated vapor (i) (ii) (iii) Determine the power of the resistor
A rigid, closed container with a volume of 0.5 m3 is heated with an electric hot plate. The vessel initially contains water as a biphasic mixture of saturated liquid and saturated vapor at 100 kPa and quality 0.5. after heating the pressure rises to 150kpa.a) Draw the initial and final states on the T-v diagram.b) Determine the temperature for each state.c) determine the mass of vapor present in each state. FOLLOW THE NEXT STEPS Step 1. Sketch/Paraphrase (Draw the sketch and process diagram if necessary) 2. Theoretical Concepts / Formulas (write down the concepts you are applying and theformulation that will help you solve the problem 3. Information (tables, data in the program, graphs) Assumptions (In the event that they arenecessary) 4.Development Solution (Pay special attention to the units shown and requested)
A vertical cylinder is fitted with a freely-moveable piston of 0.2 m diameter and contains 0.1 kg of (liquid) water. At the initial State 1, the water remains in equilibrium as saturated liquid at 15 "C with the piston applying a pressure of 7.0 bar on the water in the cylinder. The water is then slowly heated until the piston rises to a height of 0.6 m above its initial position to reach the equiliorium at State 2. The piston is now held fixed at this location and the cylinder contents are further heated to increase its pressure to 15 bar at State 3. (a) Find the volume of water at State 1. (b) Show that the cylinder contains saturated (wet) steam at State 2 and determine its dryness fraction at this state. (c) Find the steam temperature at State 3. On a T-v diagram, indicate the process undergone by the contents of the cylinder from State 1 to State 3.
Using the steam tables, given a 0.085-m3 drum contains with wet steam at 371.5oC, (a) find the respective masses of the saturated vapor and saturated liquid in the mixture if they occupy equal volume. (b) find the respective volumes of the saturated liquid and saturated vapor in the mixture if their masses are equal.
Using the tables for water, determine the specified property data at the indicated states. (a) At p = 3 bar, v = 0.3 m³ /kg, find T in °C and u in kJ/kg. T = U = (b) At T = 320°C, v = p = U = V = h = °C P = kJ/kg = 0.034 m³ /kg, find p in MPa and u in kJ/kg. (c) At p = 28 MPa, T = 400 °C, find v in m³ /kg and h in kJ/kg. m³/kg h = MPa kJ/kg (d) At T = 10°C, v = 100 m³ /kg, find p in kPa and h in kJ/kg. kJ/kg kPa kJ/kg
An ideal gas initially occupying 0.020 m3 at 1.0 MPa is quasistatically expanded inside a piston-cylinder device at a constant pressure until its volume doubles. Next the expansion is continued at constant volume till the pressure reaches half of the initial pressure. Finally it is brought back to the initial state in a polytropic process with exponent n=1.6 a) Draw the processes on a P-v diagram and calculate the total work. b) Calculate the total heat transfered, what is the difference between the initial and final temperature?
Air in a rigid tank is at 200oC and 150 kPa. The air is cooled to a final equilibrium state of 60oC . i. Determine the change in pressure of the air, kPa. ii. Show and label the process on a temperature versus volume (P-v ) diagram. The gas constant for air, R is 0.287 kJ/kg.K and the universal gas constant, Ru is 8.314 kJ/kmol.K.
A piston-cylinder device contains an ideal gas of nitrogen. At the initial state, the volume is V1= 1.00 m3, the pressure is p1= 400.00 kPa, the temperature is T1= 300.00 K. An electric heater within the device is turned on for a time of Δt = 5.00 min. The current is I = 3.00 A, and the source voltage is V = 120.00 V. During the heating process, the gas expands, and a heat loss of Qout = 2.80 kJ occurs. The gas constant is R = 0.297 kPa·m3/(kg·K), and the room temperature specific heat at constant pressure is cp =1.039 kJ/(kg·K). Calculate the electrical work done on the gas, Wele__________ (kJ)
A piston-cylinder device containing 2kg of saturated H20 at 187 °C has initial specific volume of 0.13 kg/m³. The H20 is then expanded to a pressure of 300 kPa and a temperature of 187 °C. Fill in the following chart of properties for each state, and plot the two states on the given graph. Show all your work on this sheet or the next. State 1 Property P (kPa) State 2 300 T (°C) v (m³/kg) u (kJ/kg) x (phase or quality) 187 187 0.13 V
One kilogram of air in a closed system initially at 27°C and 200 kPa receives 120 kJ of heat at constant volume. The system then undergoes a constant pressure process such that the final temperature of the air is 50°C. Show the process on a p-V diagram, giving the values of p, each state. Find the total work and the heat transferred during these processes. V and T in
Dont copy from others and answer should match. A large kitchen pot initially contains 5 kg of water at 25°C. A burner is turned on and heat is added to the water at a rate of 500 cal/sec. Determine how many minutes it will take for one-half of the mass to evaporate at standard atmospheric pressure.