A pipe increases in diameter from 300mm to 600mm. It contains a flowing oil (sp. gr. = 0.86). The difference in the level of oil in the piezometer tubes between points 1 and 2 is 360mm. Determine the actual discharge if the coefficient of discharge C = 0.8969.

A pipe increases in diameter from 300mm to 600mm. It contains a flowing oil (sp. gr. = 0.86). The difference in the level of oil in the piezometer tubes between points 1 and 2 is 360mm. Determine the actual discharge if the coefficient of discharge C = 0.8969.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Crude oil (with specific weight γoil = 55 lb/ft3 ) is pumped at a rate of 400 gallons per minute…

A: Given data, Q = 400 gallons/min = 4007.48×60ft3/s density of soil (γoil) = 55 lb/ft3pressure at A…

Q: QSDistillation columns are used to separate chemical substances based on the differences in their…

A: To find the equation of plate and surface area not covered by the bubble caps

Q: 1. A venturi meter is used to measure the water flow in a pipe with the diameter of 85mm. The…

Q: Oil flows at a flow rate of 0.030 (m³/s) in two pipes Connected in Series upwards from point No. (1)…

A: Flow rate, Q = 0.03 m3/s Length , L1 = 700 m Length, L2 = 1 km or 1000m

Q: head lost in the pipe is 30 m and the Reynolds number is 1800. a. What is the friction factor f? b.…

A: Given- head loss = 30 m L = 20 m Re = 1800

Q: Alm-diameter pipe bend shown in the diagram is carrying crude oil (S=0.94) with a steady flow rate…

Q: For constant density flow through this round nozzle, V₁ = 1.7 m/s and V₂ = 20 m/s. The ratio of…

Q: 11. From the figure shown, the tank contains oil having a sg = 0.82. Oil flows at a certain rate…

A: specific gravity of oil(s) =0.82fluid head = 2.8 m power (P) =9 hpDiameter of orffice =80…

Q: The diameter of a pipeline at point 1 is 75 mm and at point 2 is 25 mm. Points 1 and 2 are at the…

A: Consider the following figure. The specific gravity is G=1.4. The pressure head at point 1 is,…

Q: 7.30 FLUS For this refinery pipe, DA = 20 cm. Dg = 14 cm, and L= 1 m. If crude oil (S = 0.90) is…

Q: A Venturi Meter has water is flowing through the Venturi Meter, the pressure in the pipe and the…

A: Given, D = 0.2 m d = 0.06 m ∆P/γ = 0.15 m

Q: An orifice with diameter 4mm and length 1mm is submerged in lic¡uid. The upstream pressure is 12MPa…

A: d = 4mm l = 1mm P1 = 12MPa P2 = 8Mpa

Q: The discharge (Q) through a horizontal pipe is depend upon the pressure drop per unit length(AP) the…

Q: A 72 mm diameter orifice discharges 0.023 m3/s of liquid under a head of 3 m. The diameter of the…

A: Calculate coefficient of discharge,Cd

Q: Oil (SG = 0.86) is passing through a horizontal pipe whose diameter increases from 150mm diameter at…

Q: Calculate the pressure in the pipe (Point A). The area of the reservoir is 100 times the area of the…

Q: The diameter of a pipeline at point 1 is 75 mm and at point 2 is 25 mm. Points 1 and 2 are at the…

A: Given: The diameter of the pipe at point 1 is 75 mm. The diameter of the pipe at point 2 is 25 mm.…

Q: The four pipes below have steady flow of an incompressible, ideal fluid with density ps. The…

A: Four manometers are given with the three pairs of options

Q: s in oil (op.gr.=o.82) e water sarface

A: Given data- Specific gravity (SG) = 0.82 Head at point A = 2m Difference between level of tubes (x)…

Q: The flow rate in a 300 mm diameter pipe is 0.226 m³/s. The flow is known to be turbulent and the…

Q: A pressurized tank discharges its alcohol through a square orifice (c = 0.64, cy = 0.97). If minor…

A: step 1-

Q: 2. A nozzle 3 m long has a diameter of 1.3 m at the upstream end and reduces linearly to 0.45 m…

A: Figure is as shown

Q: A circular tank has an 34mm diameter orifice on one of its sides discharging oil with a specific…

Q: A solvent used for plastic manufacturing consists of cyclohexanol in tank A and ethyl lactate in…

A: Specicific gravity of cyclohexanol, Sc=0.953Specific gravity of mercury, SHg=13.55Specific gravity…

Q: Home Work P.3.1 Two pipes A andB carrying water are connected by a connecting tube as shown in…

A: The figure is as shown

Q: to the end of a 350 mm pipe. The pressure at the base of the nozzle where it joins the pipe is 415…

A: Given:- To find:- Velocity of jet

Q: cylindrical liquids, (s=1.05) respectively. An orifice 100 mm at the bottom with a discharge of…

Q: : liquid level in

A: To find : Ratio of rise in liquid. Given : The ratio of the surface tension S and density ρ of…

Q: the time required for the depth of the liquid in the tank to decrease by 1m.

A: given data volume of tank

Q: 2. A nozzle 3 m long has a diameter of 1.3 m at the upstream end and reduces linearly to 0.45 m…

A: As per Bartleby policy i can answer only one question at a time. Please upload other questions…

Q: 1.5 т 0.2 m Bottom surface of the 2.XX т cylindrical tank FR 6 т Figure Q2 (a) Determine the…

A: Unit weight of ethyl alcohol=7.74 kN/m3 h=1.5m D=2.07m

Q: 6-mm diameter orifice discharges 0.022 m3/s of liquid under a head of 3.5. The diamete jet at the…

Q: For the open tank, the piezometers attached on the side, containing two different immiscible…

Q: An orifice in the side of a tank discharges water under a head of 10ft. If the diameter of the…

A: Given:- Head of water, H=10 ftDiamter of orific, d=2 mCoefficient of contraction=0.63Lead loss=0.8…

Q: A cylindrical tank of water is 2.0 m in diameter and 3.5 m tall. There is a 1.0 cm diameter hole at…

A: *Multiple Sub- parts* As per our company guidelines we are supposed to answer ?️only first 3️⃣…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

len3
1- Water flows through a horizontal pipe at a rate of 9.1 L/s. The pipe consists of two sections of diameters 10.16 cm and 5.08 cm with a smooth reducing section. The pressure difference between the two pipe sections is measured by a mercury manometer. Neglecting frictional effects, (a) determine the differential height of mercury between the two pipe sections. (b) How would the reading change if the manometer on the 2in pipe is replaced by a pitot tube? 10.16 5.08 h
With a=4 b=1 c=1
Fluid.mec
An ideal liquid flowing through a pipe A of cross-section 0.2m² with velocity 10m/s enters a T-junction. One side of the T-junction B has cross-section area 0.1m² and the other side Chascross-section area 0.05m². If the velocity of water in C is 15m/s then in B the velocity is
A municipality wants to determine the flow rate into the plant based on pipe size, elevation difference, and assumed roughness, for the water supply reservoir is shown in the figure below. The pipe is an old 4-inch diameter Cast Iron with a Hazen Roughness coefficient of 100 & 223 feet long. The difference in elevation is 62 feet. The pipe has a strainer at the entrance (k-1.9), a valve (k=8.6), a check valve (k = 2:7) and 3- 90° bends (k-0.83). The flow exits into a receiving pond at the WTP. Provide the flow rate in Gallons Minute. per WTP Az
nat3
Orifice meter with orifice cross-section 0.00785 m2 is inserted in a pipe of cross-section 0.0314 m2. The pressure gauges fitted upstream and downstream of orifice give reading of 19.62 N/cm2 and 9.81 N/cm2 respectively. Determine the value of discharge using Cd=0.6.
1. [Ch4 – 2] A hydraulic oil with the absolute viscosity of 0.09 N.s/m² and specific gravity of 0.9, is flowing in a 30-mm- diameter pipe at a velocity of 6 m/'s, detemine: a. The Reynolds number? Is the flow laminar or turbulent? b. The head loss due to friction in units of bars for a 100-m length of smooth pipe. 2. [Ch4 - 2] The kinematic viscosity of a hydraulic oil is 0.0001 m/s. If it is flowing in a 20-mm- diameter commercial steel pipe, find the friction factor for: a. The velocity of 5 m/s b. The velocity of 50 m/s