A pipe flowing water has a manometer attached, as shown in the figure. The local atmospheric pressure, Po, is 101.3 kPa and the gravitational acceleration is 9.81 m/s². The densities of the water (pw), oil (Pon), and mercury (pug) are 1000.0, 800.0 and 13,600 kg/m³, respectively. The heights of the liquid levels in the manometer system are indicated in the figure. What is the absolute pressure at the center of the water pipe, Pw, in kPa.

A pipe flowing water has a manometer attached, as shown in the figure. The local atmospheric pressure, Po, is 101.3 kPa and the gravitational acceleration is 9.81 m/s². The densities of the water (pw), oil (Pon), and mercury (pug) are 1000.0, 800.0 and 13,600 kg/m³, respectively. The heights of the liquid levels in the manometer system are indicated in the figure. What is the absolute pressure at the center of the water pipe, Pw, in kPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure belows shows a closed tank holding air and oil to which is connected a U-tube mercury manometer and a pressure gage, with L1 = 3 ft, L2 = 0.5 ft, and L3 = 1.75 ft. The densities of the oil and mercury are 55 and 845, respectively, each in Ib/ft?. Let g = 32.2 ft/s?. Pressure gage Air Oil (p = 55 Ivit) Pam Mercury (p= 845 Ih/n') g= 322 fus? Determine the reading of the pressure gage, in Ibf/in.? (gage). Pgage = i Ibf/in.2
The sketch shows an oil manometer that is connected between two pipes which transport water. The density of water can be taken as 998kg/m3, the specific gravity of glycerol is 0.76 and atmospheric pressure is 100 kPa. The respective dimensions (as shown on the sketch) are given below: h1 = 0.17 m h2 = 350 mm h3 =15cm. From the given data, calculate the pressure difference between the two pipes.
(5) Pressure Cooker (6) Carburetor (7) Radiator of an automobile. 2. Convert the following reading of pressure to kPa, assuming that the barometer reads 760mm Hg. (1) 90cm Hg gauge (2) 40cm Hg vacuum (3) 1.2m H20 gauge 3. Five masses in a region where the acceleration due to gravity is 30, 5 ft/s are as follows: m, is-
The inclined tube manometer shown in the next figure is used to measure small pressure perturbations (Ap). This manometer is composed of a large tube (diameter (D), area (A)) and a small inclined capillary tube (diameter (d), area (a)) and angle (0). Any small pressure difference will result in fluid displacement (Ah) in the large tube and a significant displacement of the fluid in the capillary at a length (AL.). Ap AL initial level Ap (1) Obtain a relationship between (Ah) and (AL) ! (hint: displaced liquid in large tube is equal to that in the small tube ) (2) What the formula for (z2 – 21) ? (hint : height between level 2 and level 1) (3) Express the pressure (Pz-P1) in terms of (AL, 0, p, g, d, and D) ? (4) At what angle should the manometer be adjusted so that (AL-5 Ah) ?
The sketch shows an oil manometer that is connected between two pipes which transport water. The density of water can be taken as 998kg/m3, the specific gravity of glycerol is 0.76 and atmospheric pressure is 100 kPa. The respective dimensions (as shown on the sketch) are given below: h1 = 0.17 m h2 = 350 mm h3 =15cm. If the pressure gauge gives a reading of 19 kPa, what is the absolute pressure in pipe B?
I need the answer as soon as possible
In Figure below all fluids are at 20 deg.C. Determine pressure at point B, if pressure at point A is 150 kPa and weight of air is neglected. Use the table below for the densities at 20 deg.C. Liquid p. kg/m Kerosene - Ammonia 608 Benzene 881 Air Carbon tetrachloride 1590 Benzene Ethanol 789 Ethylene glycol Freon 12 B 1117 40 cm 9 cm 1327 20 cm Gasoline 680 14 cm Glycerin Kerosene 1260 t8 cm 804 Mercury- Water Mercury Methanol 13,550 791 SAE 10W oil 870 SAE 10W30 oil 876 SAE 30W oil 891 SAE 50W oil 902 Water 998 Seawater (30%e) 1025
The figure shows a sensor indicating a gauge pressure reading of 1.5 kPa. The fluids are at 20°C Determine: a) the height hb. b) the height hc.The specific weight of air is 12.0 N/m3.
Consider the liquid ina barometer whose coefficient of volume expansionis 5,5 x 10*C Find the relative change in liquid's height if the temperature charges by 13 °Cwhile the pressure remains constant, Neglect the expansion of the glass tube. Number Units This answer has no units * (destrees) kg Hint m/s
There are different types of pressures: atmospheric, barometric, gauge, absolute and vacuum pressure. Refer to Figure 5.18 below: Vacuum Vacuum Helium 20inHg Helium 30inHg , 宁大 (a) (b) (c) (a) What kind of pressure (the 20 inHg) is measured in Figure 5.18 (a)? (b) What kind of pressure (the 30 inHg) is measured in Figure 5.18 (b)? (c) What would the h reading Figure 5.18 (c) assuming that the pressure and temperature inside and outside the helium tank are the same as in part (a) and (b)?
A well is 3500 meters deep and 3100 meters vertically deep. It is filled with two drilling fluids, the first with a density of 10.5 lb/gal located up to 1000 meters and the rest of the well is filled to the bottom with fluid with a density of 12 lb/gal. During the operation, a wellhead pressure equivalent to 320 psi was recorded. With these data in hand, the pressures occurred at the bottom of the well and the equivalent density of the bottom of the well in lb/gal are, respectively: The. 6389 psi/12.12 lbs/gal 6429 psi/ 12.1 lbs/gal 5959 psl/13.2 lbs/gal 6220 psi/11.9 lbs/gal E 20:13 + 130% =
For the inclined-tube manometer of Figure Q1(b), the pressure in pipe A is 8 kPa. Thefluid in both pipes A and B is water, and the gage fluid in the manometer has a specificgravity of 2.6. What is the pressure in pipe B corresponding to the differential readingshown?