A person is pushing two boxes placed side by side with each other. What is the acceleration caused by the applied force if the net force is 253.22, the coefficient of kinetic friction of the boxes is 0.74 and the sum of the mass of the boxes is 91.05kg?  Is it possible to have one of the boxes generate an applied force of 144.34N, if yes, what is the mass of the other box?

Q: Energy Example A box of mass 15 kg is released from rest on an inclined surface with a restraining…

A:

Q: A teacup fell was left on the wing of a fighter jet and did not fall until the jet was already very…

A: It is given that the teacup is under free fall.

Q: If the maximum length of the spring is 40 cm, what average friction force opposes the motion of the…

A:

Q: What will the speed of the mass be when it has moved a total distance of 1.0 m up the incline from…

A: For solution refer below images.

Q: A 100 kg crate slides down a ramp, starting from rest. The ramp is inclined at an angle of 21.9…

A: Let the normal force exerted on the body is N Newton.

Q: A block with a mass of 100 kg slides down an inclined surface that is 5 m long and makes an angle of…

A:

Q: (b) A weight, as shown in figure Qlb-(a) has to move at constant velocity of 2 m/s on an inclined…

A: Let F1 =force applied in horizontal direction  N=Normal reaction on inclined plane  f=friction…

Q: 1. It takes 20 seconds to lift a 1600-kg car and the underlying 300-kg platform of a hydraulic lift…

A:

Q: A block of mass m1 = 20Kg is attached by an ideal pulley to a block of mass m2 = 2.5 kg on the…

A: (A) Write the given data. m1=20 kgm2=2.5 kgμ=0.4d=0.75 m

Q: A horizontal force of magnitude 45.3 N pushes a block of mass 4.26 kg across a floor where the…

A:

Q: A gyroscope is pulled with a 30 cm long string.  The string is wrapped around a 2.0 mm diameter axle…

A:

Q: Compute the Work done in moving object of 8.88 kg through distance of 3 m when force applied of…

A:

Q: upward in a plane inclined 30 ° from the horizontal, at a speed of 18 m / s. How fast will that mass…

A:

Q: A rope of length L = 2.2 m and mass m = 5 kg is initially at rest and can slide on an inclined surf…

A: It is asked to calculate the work done by friction as a function of y

Q: A 783 kg cart is pulled along a level surface by an engine. The coefficient of friction between the…

A:

Q: A 10 kg block, as seen in figure 1, is dropped from a certain height onto an uncompressed spring…

A: Given:m=10 KgK=622.6 N/mF=2.5 Nx=1 m

Q: A10-kg box resting on a horizontal surface is pulled by a 5.0 N force. A 3.0 N friction force…

A:

Q: A damaged 1310-kg car is being towed by a truck. Neglecting the friction, air drag, and rolling…

A: Given Data

Q: g at 105km/h.

A: given data  mass of the car  = 1200 kg car velocity = 105km/h                   = 105x5/18 = 29.16…

Q: A block of 50 kg is attached to a cable. The cable is then attached to a rotating assembly with a…

A:

Q: In a movie, a 1200 kg car falls a vertical distance of 24 m starting from rest. What is the work…

A: Given:Mass of car, m = 1200 kgVertical distance, h = 24 mInitial velocity, u = 0 ( starting from…

Q: A car traveling at 30 ft/s can brake to a stop within 30ft. Assume that the braking force is…

A:

Q: A block with a mass of 100 kg slides down an inclined surface that is 5 m long and makes an angle of…

A:

Q: A 20 kg pulley with a 0.5 m radius is initially at rest. The rotational inertia of the pulley is…

A:

Q: is applied on the block as shown in the figure. The magnitude of force of friction (in N) on the…

A: given data; As shown in fig; block of mass  10 kg rests on a horizontal floor acceleration due to…

Q: #5) A person is pulling a 52 kg of box up the hill that has an angle 45° above the horizontal at…

A:

Q: A father builds a swing for his children. The swing consists board attached to two ropes, as shown…

A:

Q: 100 W power supply.  What is the maximum speed the motor could lift a 10 kg mass straight up?  What…

A: given:mass m=10kgη=98%power supply =100w

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.