A person is donating blood. The 0.36 L bag in which the blood is collected is initially flat and is at atmospheric pressure. Neglect the initial mass of air in the 2.8 mm ID., 1.3 m-long plastic tube carrying blood to the bag. The average blood pressure in the vein is 46 mm Hg above atmospheric pressure. Estimate the time required for the person to donate 0.36 L of blood. Assume that blood has a specific gravity of 1.064 and a viscosity of 0.0058 Pa.s. The needle's I.D. is 1.14 mm and the needle length is 5.6 cm. The bag is 30.5 cm below the needle inlet and the vein's I.D. is 2.8 mm. Your answer should be in S. Answer:

A person is donating blood. The 0.36 L bag in which the blood is collected is initially flat and is at atmospheric pressure. Neglect the initial mass of air in the 2.8 mm ID., 1.3 m-long plastic tube carrying blood to the bag. The average blood pressure in the vein is 46 mm Hg above atmospheric pressure. Estimate the time required for the person to donate 0.36 L of blood. Assume that blood has a specific gravity of 1.064 and a viscosity of 0.0058 Pa.s. The needle's I.D. is 1.14 mm and the needle length is 5.6 cm. The bag is 30.5 cm below the needle inlet and the vein's I.D. is 2.8 mm. Your answer should be in S. Answer:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A cylinder has 40 holes evenly spaced around its surface. Each hole has a diameter of 2.5mm. One end…

Q: Freshwater and seawater flowing in parallel horizontal pipelines are connected to each other by a…

A: hw=50 cm = 0.5 mhHg = 10 cm = 0.1 mhsea = 30 cm = 0.3 mdensity = 1035 kg/m3

Q: An infinite plate is moving at a constant velocity of 3m/s over a second stationary plate. A thin…

A: Given:Constant velocity of the plate, V=3 m/sViscosity of the liquid, μ=0.65 cpsSpecific gravity,…

Q: 1. If the pressure gage, A, in figure 1 reads 2.5kPa. Determine the elevation of the liquid levels…

Q: If the fluid rises to a height of 160 mm, we write its gauge pressure as 160 mm H2O. (a) Express…

A: Solution:

Q: The device shown is the buoyancy measurement device used to measure the liquid height change. A…

A: GivenForce measured by the force sensor, Fsensor=7.53 NDistance of force sensor from the pivot,…

Q: calculate the volume of air at the reduced pressure.

A: Given: V1=0.25 m3P1=1700 kPaT1=18°CIso thermal processP2=Patm=101.325 kPa To determine: Volume at…

Q: 3. The space between two parallel plates 5 mm apart is filled with crude oil. A force of 2 N is…

Q: A u_tube whose arms are open to the atmosphere. Now equal volumes of water and light oil. (density…

Q: The fabrication shop at the university has a request to make a large outdoor barbeque cooker for…

Q: A capillary tube of 1.55 mm diameter is immersed vertically in water exposed to the atmosphere.…

Q: Working for an engineering consultancy firm, your knowledge of fluid dynamics is required to design…

A: Maximum operating pressure = 0.76 MPa = 760 kPaDiameter of the pipe, d = 150 mm

Q: A submarine is modeled as a cylinder with a length of 240 ft, a diameter of 50 ft, and a conning…

Q: Strictly don't write the Equation directly, Include Proper explanation. The maximum blood pressure…

A: The general expression for the gauge pressure read by any liquid column is as follows-Here, is the…

Q: 3. Consider a 0.15 mm diameter air bubble in a liquid. Determine the pressure difference between the…

A: Given Diameter of bubble = 0.15 mm It is asked to find excess pressure in bubble for surface…

Q: When a 2-mm-diameter tube is inserted into a liquid in an open tank, the liquid is observed to rise…

Q: Question 2 A spray bottle is used to spray small droplets of carbon tetrachloride. Determine the…

Q: The maximum blood pressure in the upper arm of a healthy person is about 120 mm Hg. If a vertical…

Q: Working for an engineering consultancy firm, your knowledge of fluid dynamics is required to design…

A: Maximum operating pressure = 0.76 MPa = 760 kPaDiameter of the pipe, d = 150 mm = 0.15 m

Q: A U-tube differential manometer connects two pressure tubes A and B. Pipe A contains carbon…

Q: An enclosed cubic tank of side length 2 m is filled with water through a vertical stand- pipe of 50…

Q: Methanol (SG=0.792) is contained in a large tank under a pressure of 350000 Pa absolute. When a…

Q: Patients suffering from decompression sickness may be treated in a hyperbaric oxygen chamber filled…

A: Given: The diameter of the cylindrical chamber is D=0.75 m The gauge pressure of oxygen in the…

Q: long, 2m deep and 3 m wide contains oil of relative density 0.9 to a depth of 0.9 m. If the tank is…

Q: Atmospheric pressure is used to lift a part with a surface area of 0.008m^2. The piece is placed in…

A: To find When the cylinder is closed, and piece rises 2m, then the weight of the piece is When the…

Q: Two vats are connected by a submerged pipe with a square cross-section, as shown in the image…

A: Note: Since you have posted a question with multiple sub-parts, we will solve first three sub- parts…

Q: The pressure in a car tire depends on the temperature of the air it contains. When that temperature…

Q: The capillary pressure for a channel of round cross section can be expressed as a function of the…

A: Write the given data. d1=2 mmθ1=80°θ2=125°P1=P2=15 mbar

Q: Check All That Apply U The pressure is lower at higher elevations. As a result, the difference…

A: Why nose bleeding and shortness of breath occur at high elevation.

Q: A two-compartment vessel contains fluid in each section. For the first compartment, the fluid…

A: To find specific gravity of mixture

Q: A mercury manometer is used to measure the pressure difference between pipes A and B. Oil (specific…

Q: Problem #4. The water in a tank is pressurized by air, and the pressure is measured by a multifluid…

A: Given data: h1=0.1 mh2=0.2 mPatm=85.6 kPa Need to determine the air pressure inside the tank.

Q: A cylinder has 40 holes evenly spaced around its surface. Each hole has a diameter of 5mm. One end…

Concept explainers

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.

Question

100%

A person is donating blood. The 0.36 L bag in which the blood is collected is initially flat and is at atmospheric pressure. Neglect the initial mass of air in
the 2.8 mm ID., 1.3 m-long plastic tube carrying blood to the bag. The average blood pressure in the vein is 46 mm Hg above atmospheric pressure.
Estimate the time required for the person to donate 0.36 L of blood. Assume that blood has a specific gravity of 1.064 and a viscosity of 0.0058 Pa.s. The
needle's I.D. is 1.14 mm and the needle length is 5.6 cm. The bag is 30.5 cm below the needle inlet and the vein's I.D. is 2.8 mm. Your answer should be in
S.
Answer:

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step by step

Solved in 6 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The diameter of one arm of a U-tube is 12 mm while the other arm is large. If the U-tube contains some water and both surfaces are exposed to atmospheric pressure, determine the difference between the water levels in the two arms. The surface tension and density of water at 20°C are σs = 0.073 N/m and ρ = 1000 kg/m3. What is the difference between the water levels in the two arms (in mm.)
The balloon has a mass of 30 g (empty) and it is filled with air having a temperature of 20 °C having the density of 1.202 kg/m³. If it is released, it begins to accelerate upward at 8 m/s?. (Figure 1) Part A Determine the initial mass flow of air from the stem. Assume the balloon is a sphere having a radius of 260 mm Express your answer using three significant figures. I1 vec ? m = g/s Figure 1 of 1 Previous Answers Request Answer Submit X Incorrect; Try Again; 4 attempts remaining 8 m/s? Provide Feedback 5 mm
One end of a tube of unknown radius is immersed to a depth of 15 mm in water and an air bubble is blown at the end of this tube. The maximum air pressure measured is 200 Pa. The same procedure is carried out in a liquid and the maximum air pressure recorded in 150 Pa. Determine the surface tension of the liquid. Data given: Density of water = 997 kg/m3 Density of liquid = 850 kg/m3 Density of air = 1.2 kg/m3 Surface tension of water = 72 mN/m
Consider a tank of rectangular cross section partially filled with a liquid placed on an inclined surface, as shown in the figure. When frictional effects are negligible, what is the relation between the slope of the liquid surface and the slope of the inclined surface when the tank released. L. Multiple Choice O O O a-B=1 α-1=ß a+B=1 a=B
Air is flowing in the wind tunnel in the laboratory. The temperature in the laboratory is 22°C and the height of the column of mercury in the barometer in the laboratory is 634 mm. The liquid in the manometer being used to measure the vacuum in the wind tunnel is oil having a specific gravity of 0.826, and the manometer reading is 125 mm . The wind tunnel is on the CU campus in Denver where g = 9.796 m/s² . a) Find the atmospheric pressure of the air in the laboratory (answer: 84092 Pa). b) Find the absolute pressure of the air in the wind tunnel (answer: 83081 Pa). c) Find the density of the air in the wind tunnel (answer: 0.981 kg/m³). Air at 22°C → h = 125 mm Oil, SG = 0.826
There is a tank with a radius of 1.0 m open to the air at the top and another tank with a radius of 0.5 m that is closed and a vacuum of -9.0 x104 Pa has been created in its upper part. Both tanks contain a fluid with S=0.92 and are initially in the position shown because the stop valve is closed. When it opens, determine: a) the height that the fluid will remain in each tank.
A capillary tube viscometer is being selected to measure viscosity of a liquid food. The maximum viscosity to be measured will be 230 cP and the maximum flow rate that can be measured accurately is 0.015 kg/min. If the tube length is 10cm and a maximum pressure of 25 Pa can be measured, determine the tube diameter to be used. The density of the product is 1000 kg/m3.
The test tube opens at 293 K with 15 cm Hg at the bottom, and 7.5 cm of water above the Hg. Calculate the pressure at the bottom of the tube if the atmospheric pressure is 760 mm Hg. Use the density of 13:55 g / cm3 for Hg and 0998 g / cm3 to air.Berikan answers in terms of dyne / cm2,psia, and kN / m2 • (see conversion table). a. … KPa. b. … Dyne / cm2. c. … Psia.
Consider a U-tube filled with mercury as shown in Figure 2. The diameter of the right arm of the U-tube is D = 2 cm, and the diameter of the left arm is twice that. Heavy oil with a specific д. gravity of 3.0 is poured into the left arm, forcing some mercury from the left arm into the right one. Determine the maximum amount of oil that can be added into the left arm. Hint: The change in volume in the left column is equal to the change in volume in the right column (Begin your solution using this hint.) ۵۷۱ -V 2 =oV Oil poured in here SG= 3.0 2D 20 cm 4CM veli D=2 cm Mercury SG= 13.6 اده
A sled with two runners slides along a thin horizontal layer of water between the ice and the runners. The horizontal force that the water puts on the runners is equal to 2.4 lb when the sled's speed is 50 ft/s. The total area of both runners in contact with the water is 0.04 ft2, and the viscosity of the water is 3.5x10 lbs/ft2. Determine the thickness of the water layer under the runners. Assume a linear velocity distribution in the water layer.
A mountain climbers observed that the pressure on top of the mountain is 500 mm Hg. At the same time the pressure at the base is 760 mm Hg. If average air temperature at that time is 28 degrees C. Calculate the approximate height of the mountain.
Milk with a density of 970 kg/m^3 is transported on a level road in a 9-m long, 3-m diameter cylindrical tanker. The tanker is completely filled with milk, i.e., no air space in the tank. If the truck is accelerating from a stop signal at 7.0 m/s^2 to the left, determine the pressure difference between the maximum and minimum pressures in the tank. Depict on the figure the location of the minimum and maximum pressures in the tank. min. 9m 3m