QUESTION 30Following on from the previous question. The tumble dryer drum gets stuck after 23.2 seconds, how manyradians will the drum have rotated in this time?(Note: If you think your answer should have units, the units should be entered in a very specific way on theblackboard site. Enter your number answer immediately followed by the unit leaving no white space. Forvelocity e.g. 33 km h* enter 33km/h (for 2 sig.fig.) or 33.00km/h (for 4 sig.fig.); for density 1000 kg m-3 enter1000kg/(m*m*m}; for work done 3x103 N m enter 3e3Nm; for area 4 m2 enter 4m*m; for mass eg. 3 kg enter 3kgor 80 tonne enter 80tonne. For radians enter rad, for degrees enter deg, for revolutions enter rev, for revolutionsper minute enter rev/min, for angular acceleration enter rad/(s*s). Any queries about how to enter units then askthe module staff team. Also make sure to put the right number of significant figures.) A particular tumble dryer process operates with a rotating drum on a regular repeating cycle. One cycle of the drumis described as follows: the drum starts from rest and then undergoes one complete revolution, during which theacceleration and retardation are uniform and at the same rate, the drum the pauses for 4.0 seconds to completeone cycle. During a drying program this cycle is repeated many times. If the total time taken for 5 complete cycles is95.0 seconds, use a angular velocity - time diagram to help you calculate:the angular acceleration of the drum.

29. In to complete every cycle the drum is paused for 4 sec. Thus, the total time of motion will be…

A particular tumble dryer process operates with a rotating drum on a regular repeating cycle. One cycle of the drum is described as follows: the drum starts from rest and then undergoes one complete revolution, during which the acceleration and retardation are uniform and at the same rate, the drum the pauses for 4.0 seconds to complete one cycle. During a drying program this cycle is repeated many times. If the total time taken for 5 complete cycles is 95.0 seconds, use a angular velocity - time diagram to help you calculate: the angular acceleration of the drum.

A particular tumble dryer process operates with a rotating drum on a regular repeating cycle. One cycle of the drum is described as follows: the drum starts from rest and then undergoes one complete revolution, during which the acceleration and retardation are uniform and at the same rate, the drum the pauses for 4.0 seconds to complete one cycle. During a drying program this cycle is repeated many times. If the total time taken for 5 complete cycles is 95.0 seconds, use a angular velocity - time diagram to help you calculate: the angular acceleration of the drum.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

The angular speed of a particular cog in a machine is given by: w(t) = Kcos (2T) +M where K = 0.57 rad s¯¹, T = 4.5 s, and M = 0.029 rad s-1 What is the angular acceleration a of the cog at a time of 12 s?
A solid disk is rotating with a constant angular speed as shown below. What statements can we make about this object? Choose all that apply. The disk has a fixed amount of angular momentum The sum of torques on this disk is zero There is a counterclockwise torque being exerted on this disk The sum of forces on this disk is zero The disk has a fixed amount of rotational energy
7 kg 3 kg 53° 49° There is no friction in the system above except between the rope and the pulley so that the rope does not slip on the pulley. The pulley is a uniform spherical shell with a mass of 1.43 kg and radius of 12 cm, and the rope does not slip on the pulley. The system is released from rest. Use work-energy principles to determine how much kinetic energy does the smaller mass have after moving d = 2.3 meters parallel to the ramp? K =
Small bodies of mass m1 and m₂ are attached to opposite ends of a thin rigid rod of length L and mass M. The rod is mounted so that it is free to rotate in a horizontal plane around a vertical axis (see below). What distance d from m₁ should the rotational axis be so that a minimum amount of work is required to set the rod rotating at an angular velocity w? (Use any variable or symbol stated above as necessary.) d= m₁ -L-d MY NOTES m₂
Problem 9: A solid ball with mass, M=2.5 kg and radius, R=0.2 meter is released from rest from the top of an incline of height, h=3.5 meter. Ignore any energy loss due to friction or air drag. Consider g=9.8 m/s2. (a) The linear speed of the ball at the bottom is ________ (b) The rotational kinetic energy of the ball at the bottom is _________
5 1.1
A thin uniform rod AB of length L and mass m is nailed to a wall through point C, which lies on the rod at the distance L/4 from point A. Assume that the rod rotates frictionlessly about the nail. Initially the rod is kept horizontal,and it is then released (a) Find the angular acceleration of the rod right after it has been released (b) find the total kinetic energy of the rod at the moment when it was vertical
A potter's wheel is rotating around a vertical axis through its center at a frequency of 1.8 rev/s . The wheel can be considered a uniform disk of mass 5.0 kg and diameter 0.34 m The potter then throws a 2.6-kg chunk of clay, approximately shaped as a flat disk of radius 7.0 cm, onto the center of the rotating wheel. - What is the frequency of the wheel after the clay sticks to it? Ignore friction
A 70 kg disk is spinning about a vertical axis of rotation with a radius of 1.2 m and a rotational inertia of 0.45 mr2 and it has an initial angular velocity of 10 rad/s. An unknown mass falls onto the disk 0.8 m away from the axis of rotation. After the collision, the disk is now spinning at 6 rad/s. The rotational inertia of the mass is mr2. Calculate the unknown mass that falls on the disk.
A car wheel ball is initially at rest at the top of a ramp. If the energy of the car wheel is to be conserved. What must be the equation of conservation of energy if we take into account translational and rotational kinetic energies. Q Zoom A 2 mv2 = 2 mv? + ½ lw? B ½ mv2 = ½ mv,? + mgh, mgh, = 2 mv? + ½ lw² D ½ mv,? + mgh, = ½ mv,? + mgh, ½ mv? + mgh, = ½ mv,? + ½ lw?
A machine has a rod-shaped steel blade that rotates about its center. The mass of the blade is 0.75 kg and its length is 0.75 . Calculate its rotational kinetic energy when the blade has reached its operating speed of 4000 rpm.
A turn table starts from rest and reaches 11 rad/s of angular velocity in 9.0 s. Find the total angle it turned during the time in rad. Hint: use rotational kinematics formula. Assume initial angle and initial angular velocity as zero. Your Answer: