I need the answer quickly A particular area can be supplied either by hydro station or steam station. Thefollowing data is available :Capital cost / Running cost/ Interest and ReservekWhStationdepreciation capacity7%9%Q6kW2000 $0.04 $30 %HydroSteam0.06 $1300 $22 %At what load factor would the overall cost be the same in both cases ? Whatwould be the cost of generating 55 x 10° units at this load factor ?

Answered: Image /qna-images/answer/5b184594-bed5-4348-b9e7-da57d48041e5.jpg

A particular area can be supplied either by hydro station or steam station. The following data is available : Capital cost/ Running cost / Interest and Reserve kWh 0.04 S 0.06 S Station depreciation capacity kW 2000 $ 1300 $ 7% Hydro Steam 30 % 9% 22 % At what load factor would the overall cost be the same in both cases ? What would be the cost of generating 55 × 10° units at this load factor ?

A particular area can be supplied either by hydro station or steam station. The following data is available : Capital cost/ Running cost / Interest and Reserve kWh 0.04 S 0.06 S Station depreciation capacity kW 2000 $ 1300 $ 7% Hydro Steam 30 % 9% 22 % At what load factor would the overall cost be the same in both cases ? What would be the cost of generating 55 × 10° units at this load factor ?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

If an electrical system operates at a potential higher than 600 volts, the nonmetallic conduit must be encased in at least_of concrete. A. 1 inch B. 2 inches C. 4 inches D. 6 inches
where is the answer?
Please answer in typing format solution please only Please answer all subparts is compulsory to answer in your Please I will like it please
The is the distance from-1 the centre of one slot to the centre of .the next slot a) coil span O b) pole pitch O c) slot pitch O
Question.
3. Which of the following statements about the use of structural steel as an equipment grounding conductor(EGC) in an AC system is correct?A. Structural steel isn't allowed for use as an EGC.B. Structural steel can be used as an EGC bonding jumper between panelboards.C. Structural steel must have an EGC bonding jumper every three feet of structure.D. Structural steel can be used as an EGC when it's bonded at both ends.
Estimate the length of conduit to perform the next bends. EMT will be bend using a hand bender. Provide your answer in inches (just the number) using up to 2 decimals. The picture shows two panels connected by a back-to-back 23.5" stubs EMT 3/4" 6.25 ft P
What is the lighting and receptacle demand load for an 1000 sq. m office space with one hundred ten, 15 A, 250 V receptacles. [Office General Lighting Receptacle]
Assuming all terminals are rated 75°C and you have a #10 AWG THHN/THWN conductors in a conduit and the conduit is run on the roof off a office building where the ambient temperature never rises above 30°C the largest size circuit breaker or fuse permitted to protect these wires is:?
The wording that I am running into with questions such as "The number of conductors required to be installed between three-way and four-way switches is " is confusing. The text is not expalining this in a way that I am understanding anything other than grounding conductor, which is optional unless I am using a metal box. So what type of "conductor" is beng discussed?
Complete the following text with words Pt100 sensors are a specific type of _____(1) detector. The most important characteristic of Pt100 elements is that they are made of _____(2) with an electrical resistance of _____(3) ohms at a temperature of ______(4) °C and temperature coefficient ____(5). It is by far the most common type of RTD sensor. The other materials with which RTDs are built are: ___(6), _____(7), ______(8). The most recommended conditioning method is reading at _____(9). Typically, a _____(10) behavior of the Resistance-Temperature relationship can be assumed.
Please answer quickly. 17. The filament of incandescent lamp is usually made of: a. copper b. silver c. aluminum d. tungsten 18. A current measuring instrument can be modified to measure voltages by: a. using thicker wire in the coil b. using a high resistance shunt c. adding resistance in series d. adding resistance in parallel 21. "When two power sources are connected in a series-aiding configuration, the output voltage equals the _____________" a. supply with the highest voltage b. supply with the lowest voltage c. difference of the two supplies d. sum of the two supplies