A |-5 5 m B 5 m C Hinge DE Hinge -6m +3m--3m- F

Q: * Assignment Construct the influence line for the vertical reaction at B and A, separately, of the…

A:

Q: A В 5m 4 m 6 m 15m

A:

Q: Draw the influence lines for the shear and bending moment at point F of the beam shown in this…

A: Step 1:Step 2: Step 3: Step 4:

Q: raw the influence lines for members DK and CI assuming that the loads in the illustrated truss are…

A:

Q: the beam subjected to a series moving loads as shown in figure 1. compute the bending moment at C…

A: To calculate the bending moment at C

Q: Question (2) For the beam shown in figure (2), draw the influence lines for: 1.…

A:

Q: Assume that the loads are being transmitted to the bottom chord in the truss depicted, and draw the…

A:

Q: A 1 —4m- с -4 m- B -4 m-

A: GIVEN:  TO CALCULATE : The influence line for the shear at point C of the beam shown above.

Q: Draw the detailed influence line for the vertical reactions and moment reactions at supports B, E,…

A: ILD is a graphical representation of variation in reaction, shear force, axial force, deflection…

Q: Derive the influence line equations and sketch the influence lines for the vertical reaction at A,…

A: Data given Find: (a) Influence line equation and diagram for vertical reaction at A (b) Influence…

Q: Determine the largest force that can be developed in member BC of the bridge truss shown due to a…

A:

Q: The moving load is transmitted to the bottom chord of the truss. F G 3 m B C D 3 panels at 4 m = 12…

A: considering joint d

Q: A bridge truss shown in Figure Q1(b) is subjected to a vertical unit load moving trom points D to L.…

A: Answer:-

Q: 3. Draw the influence lines for the vertical reactions at supports A and E, the reaction moment at…

A: In this question we are asked to draw  ILD of given stress functions

Q: 16m 16 6m

A:

Q: For the beam shown, using the Müller-Breslau principle, do the following: (a) Draw the influence…

A:

Q: For the beam with one end overhanging support B, as shown in Figure, construct the influence lines…

A:

Q: Sketch the influence lines for the vertical reaction at A and the shear at C. Also, using these…

A:

Q: Draw the influence line for vertical reaction at support A. A В C D -1.6 m -1.6 m -1 m-

A:

Q: a For the beam shown in the figure: a. Draw the influence line for reaction at A, for shear just to…

A: In order to draw the qualitative ILD use Muller Breslau principle . Draw the deflected shapes…

Q: For the beam and loadings shown, determine the following: 1. Calculate the vertical force reaction…

A: ∑ME=0VB×8 - 12×600×6×5+13×6 - 1200×3 - 3000=0VB=2400 N ↑∑V=0VB+VE=12×600×6 + 12002400+VE=12×600×6 +…

Q: Influence Lines. , (a) For the determinate beam shown below, draw the Qualitative influence lines…

A: Influence line represents variation in Forces w.r.t Load.

Q: A bridge truss and a system of moving concentrated load are shown below. The bridge truss: A The…

A: Given: Point loads: P1=25 kNP2=30 kNP3=30 kNP4=50kN To find: ILD for member BC and calculate the…

Q: Example Draw the influence lines for the for reaction at support A ( RA), shear force at point D (…

A: Given data in question  Proppee cantilever beam  Span member length  Internal hinge To find out…

Q: 2. For the truss shown, construct the influence lines for the bar force or component in each of the…

A:

Q: Refer to the beam shown below a. Draw the influence line for the vertical reaction at  internal…

A:

Q: or the shear at S ? Pleas

A:

Q: -hinge sm

A:

Q: Draw the Influence Line Diagrams for Shear at point C for the beam shown below. Plot the values at 1…

A: Influence Line diagrams represents the changing value of the reactions, shear force and bending…

Q: a. Draw the Influence Lines for all support reactions, shear and moment at B b. Determine the…

A: Given simply supported beam and asked to determine the following,1. Draw the Influence Lines for all…

Q: A DRAW REACTIONS, 1.0 ठे X 71771 NOTE: THE 31 INFLUENCE PIAGRAM SHEAR 7-x 4¹ 2 AND MOVE THE 1.0…

A:

Q: C 5m A * 4m D 6m B

A: Using Muller Breslau Principle to draw the ILD for given internal/external . For bending moment ILD…

Q: D 2m. 2m

A: Sign convention used for ILD:Influence line for reaction is positive if the reaction acts upwards.…

Q: Q2 Use the Müller-Breslau principle to sketch the influence lines for the vertical reaction at A,…

A:

Equilibrium and Support Reactions

Civil engineers deal with structures that are composed of several members connected or with individual members such as beams and columns. To analyze such structures, the condition of statics must be applied. Under the static condition, the members are considered to be in equilibrium under the action of forces, that is, the members are assumed to be having negligible velocity.