A o 25 mm hole is pierced in a t = 2.5 mm thick steel sheet having shear strength t = 350 MPa. If the diametral clearance is given by the expression c = 0.00641T, the die diameter (in mm), punch diameter (in mm) and punch force in (kN) respectively are %3D

Q: Where is the Energy Balance?

A: to find energy balance we need to write the mechanical energy conservation equation i.e. bernoulis…

Q: How does heat transfer over time ?

A: Heat transfer is the mode by which energy in the form of heat is transferred from one location to…

Q: Bookmark Question Challenge This Question Safety glasses are required to be worn: Owhenever there is…

A: ● Safety glasses are used for protection. ● Foreign material are unwanted material which arise due…

Q: Describe how the wind turbine works.

A: The wind turbine as name suggests, the main energy sources comes from kinetic energy of the wind.…

Q: What kind of situation might happened to the engine due to too high temperture?

A: Let us discuss effects of high temperature on engine.

Q: what is the minimum energy to do a 1kw power

A: Given: Power, P = 1 kW = 1000 W Energy, E = ?

Q: What is the waterline

A: Solution:   The correct answer with necessary explanation is given below:

Q: To prevent a manual-type torch from damage, it is madeof a special plastic that resists what?

A: The plasma torch is a device that allows the creation and control of the plasma for welding or…

Q: Mention the basic flame types a

A: Given: Basic Flame types

Q: Engine working principle

A: ENGINE WORKING PRINCIPLE: A engine is a machine, which converts heat energy into mechanical energy.…

Q: d) Is that possible? e) Draw a heat engine diagram of a perpetual motion machine. f) Is it possible…

A: following is the answer to the above question

Q: what is the temp gradient and direction

A:

Q: Draw the Ts diagram of the whole process

A:

Q: Talking about the material from which the air conditioner compressor is made with a presentation of…

A: The compressor is in charge of transferring the refrigerant between the evaporator and condenser…

Q: What are the four ways we put fluids to work

A: Crystalloid IV solutions contain small molecules that flow easily across semipermeable membranes.…

Q: Q1: Explain what do we mean by rectifier? How it works, what type of welding machines have a…

A:

Q: Question: - Explain the Concept of mean temperature of heat addition.

A: The answer is given in next step

Q: Different types of IC engines

A: Given:

Q: List any four limitations of using conventional energy sources

A: There are two main sources of energy which can be written as below, 1. Source of conventional type…

Q: es several activities divided into three groups and these

A: The average time required to troubleshoot and repair failed equipment is measured by the mean time…

Q: Please all solve the problem

A:

Q: • A 6 MW generator had a thrust of 103,000 lb. The outside diameter of the step bearing is 12 in,…

A:

Q: The rotation angle of the joints is still needed.

A:

Q: Comparision between pulverized coal firing and stoker firing.

A: Pulverized coal firing and stoker firing are two common methods used for combustion in boilers to…

Q: -Drilled hole TERMINAL

A: finish missing views and lines.

Q: What is the maximum gas flow rate for a nozzle size?

A: GIVEN; What is the maximum gas flow rate for a nozzle size?

Q: What is the simplest industrial piping system (simplest to design and develop)?

A: The objective of the question is to identify the simplest industrial piping system in terms of…

Q: Q4 After losing a race championship with few points, a constructor was eager to boost their vehicle…

A: In IC engines a carburetor's function is to air and fuel to supply to the engine. Its primary…

Q: Reflector is used in solar dryer. Select one: True False

A: We are to determine if reflector is used in solar dryer

Q: The optimum effective temperature for human comfort is ?

A: For a human being,

Q: What does “ambient” temperature mean?

A: Measurement of bodie's hotness or coolness is known as temperature. Units : °C, °F, °K

Q: how did you get the 3038Pa in static pressure?

A:

Q: Which one of the following statement is correct for steam nozzle? O a. Outlet velocity of the steam…

A: Let us first understand how steam nozzle works: Steam nozzles are generally used in power plants…

Q: Choose the correct answer The discharge pressure of a refrigerant should be as constant as possible…

A: In a refrigeration cycle the refregerant flows through the pipes into the compressor where it…

Q: Friction less cannot be with cutting surfaces, during ansys simulation True False

A: Friction less cannot be with cutting surfaces, during ansys simulation True False

Q: What is the minimum gas flow rate for a nozzle size?

A: Given: What is the minimum gas flow rate for a nozzle size?

Q: State two types of the core in rigging

A: It is asked to explain two types of core rigging

Q: What is the applications Center of Pressure

A: Center of pressure: It is the point at which the total sum of a pressure field acts on an object…

Q: Seam-welding is .6 Multi-spot welding process Continuous spot welding process Used to form mesh )…

A: Seam welding is a type of resistance welding in which two rollers act as electrode between which…

Q: What the differences between from the following: -Natural and refinery gas -Thermal and catalytic…

A:

Q: which type of furnace is used for installation in a crawl space?

A: To explain: The type of furnace is used for installation in a crawl space.  Concept used: Crawl…

Q: Mechanical working of metal is another name for O a. Casting process O b. Machining process O c.…

A: Mechanical working is forming process .. there are two types of working cold and hot working.

Q: hat does back work ratio mean and should it be greater than one?

A: In  turbine  air expend and produced work. The part of the the work is being utilized to run the…

Q: What is stand for AFUE and explain its efficiency system

A: AFUE stands for Annual Fuel Utilization Efficiency.

Q: Why is crankcase ventilation necessary?

A: The crankcase ventilation is important in IC engine.