A non-compressible aqueous slurry has filtering characteristics such that K = 1.44 × 10-6 for Q in tonnes/cycle. If slurry is to be filtered at constant pressure in a plate and frame filter press at a rate to process an average of 1 tonne per hour of feed and it is to be washed with an equal amount of water equal to on-eighth the volume of filtrate, The dumping and assembling time is 6 hrs. The plant operates 6000 hrs/yr and the slurry feed contains 12% wt solids and the cake contains 72% solids. Annual fixed cost may be taken as Rs. 20/m² of filtering area. Direct cost is Rs. 4.33/m² Cleaning cost is Rs. 8.12 /m² of filtering area. What is the minimum annual total cost and the optimum cycle time?

A non-compressible aqueous slurry has filtering characteristics such that K = 1.44 × 10-6 for Q in tonnes/cycle. If slurry is to be filtered at constant pressure in a plate and frame filter press at a rate to process an average of 1 tonne per hour of feed and it is to be washed with an equal amount of water equal to on-eighth the volume of filtrate, The dumping and assembling time is 6 hrs. The plant operates 6000 hrs/yr and the slurry feed contains 12% wt solids and the cake contains 72% solids. Annual fixed cost may be taken as Rs. 20/m² of filtering area. Direct cost is Rs. 4.33/m² Cleaning cost is Rs. 8.12 /m² of filtering area. What is the minimum annual total cost and the optimum cycle time?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A diode generator is required to produce 17 mV of noise in a receiver with an input impedance of 52 W and a noise power bandwidth of 240 kHz. Determine the current through the diode in milliamperes. No need for a solution. Just write your numeric answer in the space provided. Round off your answer to 2 decimal places.
Specify the LM-series linear regulator required to regulate a fixed voltage of -19 V. Please write the numbers only in the answer field: i.e. for LM1234, you would write 1234 in the answer field.
Attampet with only two: 1: Prove that the dynamic resistance of diode is ra=26mv/Ip. 2:Prove that the ripple voltage of HWR is Viru=V+Vde and the ripple factor of HWR 121%, u=40.5%. 3: Using silicon diode design a clamper that will produce output V-20Sin wt+10 (v) when the input voltage is Vo=20Sin wt-10 (V).Draw the circuit diagram and the input and output signals. 4:The 6-V zener diode has a maximum rated power dissipated of 690 mw.Its reveres current must be at least 3mA to keep it in breakdown. Find a suitable value for Rs if V; can vary from 9v to 12v and Ri. can vary from 5000 to 1.2KO.
None
Haritalar A (99+) Academia.ed... BUZEM Türkçe (tr) ▼ O Power Electronics_1 slerim / Çeşitli / MÜHENDİSLİK FAKÜLTESİ / Elektrik Elektronik Mühendisliği (İngilizce) / E2E350_Power Electronics 1/ 10 For controlled half wave rectifier, R=84ohm, f=50Hz and Vm=280V and a=1,5 rad. Calculate the power (W) absorbed by the load. Yanıt: In your calculations, take 3 digits after the comma and take pi = 3,14; Enter your answer into the system in terms of the desired unit only as a number.
Q1. Determine the ripple factor for the full-wave rectifier circuit with LC filter shown below. 80 mH 52 200 sin 120rt 118 μf 50Ω
An oscilloscope is to be have aninpit resistance of 8Mga sensitivity of 50 mv. and atten uation Sactorof 4,10,40 , l00 and 40 • Calculate the values of the attenuating resista and the Volt /div valuescorresponding to each attenuatian factore Asume Ri offthe vertical Amplifia is sufficiently high to be ignored.
贪0l ۲ من ۲ • Asiacell Il. A docs.google.com Choose Conectarnswer Saly ihii Using the approximate equivalent -2 model of a silicon diode and taking E=10 V and R=1k, what is the value of * ?diode voltage at operating point c) 10 V O a) 0.7 V O d) 9.3 V b) 0.3 V O نقطة واحدة DC resistance of diode is -4 measured at b) Cut-in voltage c) Q-point a) Knee current d) Reverse breakdown point نقطة واحدة What will happen when a p-n -1 حہسہن و 8:07. äc lul 21.02.27
Kindly answer the following question (as soon as possible) #37
(g) Explain absolutc and relative stability and name two methods for cach.
16. SF6 gas major disadvantages include: It is toxic B) It cannot be pressured C) Chemically unstable D) All are correct
Reduce the following block diagrams ill tisll bbidll usisl +, 63 Hi 6 G4 6.