I need the answer as soon as possible A multi disc clutch transmits 55KW of power at 1800 rpm. Coefficient of friction forthe friction surface is 0.1. Axial intensity of pressure is not to exceed 160KN/m². Theinternal radius is 80 mm and is 0.7 times the external radius. Find the number ofplates needed to transmit the required torque assuming uniform wear conditions.

Answered: Image /qna-images/answer/d006e189-342f-4a71-b774-403090456621.jpg

A multi disc clutch transmits 55kW of power at 1800 rpm. Coefficient of friction for the friction surface is 0.1. Axial intensity of pressure is not to exceed 160kNIm. The internal radius is 80 mm and is 0.7 times the external radius. Find the number of plates needed to transmit the required torque assuming uniform wear conditions.

A multi disc clutch transmits 55kW of power at 1800 rpm. Coefficient of friction for the friction surface is 0.1. Axial intensity of pressure is not to exceed 160kNIm. The internal radius is 80 mm and is 0.7 times the external radius. Find the number of plates needed to transmit the required torque assuming uniform wear conditions.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

It is the ability of a liquid to spread out.
Suppose a hippopotamus on land receives 73 units of heat per minute due to solar radiation and 52 units of heat per minute due to infrared radiation. It emits 39 units of infrared radiation and it loses 66 units heat per minute through evaporation. The hippopotamus gains 45 units of heat per minute through its metabolism. Overall, its heat energy is increasing by 50 units per minute (i.e. its temperature is increasing). Delta Hanimal = SR + IRin - IRout ± Hconv ± Hcond - Hevap + Hmet Based on this information we can conclude that the combination of conduction and convection is the animal, and that its current temperature is than the ambient temperature. Select one: a. cooling; warmer b. warming; warmer c. cooling; cooler d. warming; cooler
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
Simple Machines-Levers, Inclined Planes, and Pulleys Directions: Use the appropriate equation to answer the following questions. All answers should be recorded below or in your Engineering Design journal. Remember to show all work. A lever has an effort arm that is 5 meters long and a resistance (load) arm that is 3.5 meters long. How much effort is needed to lift a 100 Newton weight? 5K i). Draw the figure representing the problem ii). How much effort is needed to lift a 100 Newton weight? iii). What is the Actual Mechanical Advantage 1. 5m i) AOON 5-5m
There may or may not be one or more mistakes in the solution. Go through the solution carefully and then do the following. 1. State if the solution is correct or incorrect 2. If the solution is incorrect, identify what is the mistake in the solution. Be specific and succinct. 3. If the solution is incorrect, provide the final solution with appropriate steps. Problem: A refrigeration cycle uses refrigerant R-134a to cool down water from 40°C to 20°C. The refrigerant R-134a enters the cycle as saturated liquid at -15°C and exits as saturated vapor at the same temperature. The mass flow rate of R-134a is 0.12 kg/s. The overall heat transfer coefficient is 1400 W/m².K. The surface area of the heat exchanger is 1.4 m². What is the rate at which heat is being exchanged between R-134a and water? Assume that the heat exchanger is perfectly insulated from outside (i.e., there is no convection or radiation with the outside/surrounding). Solution: We know, from the definition of overall heat…
can you please provide the solution for the answer in Reaction Ay?
Q. Define : Mechanical efficiency.
When does force work?
What’s the correct answer please?
The solution (298.349) is incorrect as well.
13. The amount of heat (Hth, thermal energy) stored in rocks, m = 500 kg, S = 840 J/(kg °C), Tfinal =50°C, Tinitial = 40°C is: ·Hth = 19*10E(6) Joules. ·Hth = 4.2 * 10E(6) Joules. %3D ·Hth = 4.2*10E(4)Joules. %3D
Describe processes occur in a certain direction, and not in the reverse direction.