A movie was shot in 150 fps. The movie lasted for 30mins. The movie was played in a vertical and horizontal pixel of 720 x 720 respectively. The bit depth for the video was 16 bit. This same video was shot having an audio sampling rate of 44100 Mhz with an audio bit depth of 32bit. The producer of the video decided to test the quality of the audio for the movie with a surround 5.1 channel audio system. 15 marks i) Calculate the audio file size in bits and explain its effect on the video file. ii) Calculate the file size of the video in Megabytes (Mb) iii) Calculate the bit rate of the video file and explain the effect of the value on processing of the file

A movie was shot in 150 fps. The movie lasted for 30mins. The movie was played in a vertical and horizontal pixel of 720 x 720 respectively. The bit depth for the video was 16 bit. This same video was shot having an audio sampling rate of 44100 Mhz with an audio bit depth of 32bit. The producer of the video decided to test the quality of the audio for the movie with a surround 5.1 channel audio system. 15 marks i) Calculate the audio file size in bits and explain its effect on the video file. ii) Calculate the file size of the video in Megabytes (Mb) iii) Calculate the bit rate of the video file and explain the effect of the value on processing of the file

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Solve this
(b) Design and draw a 8:1 multiplexer
A stabilized multivibrator is made up of 2 NAND gates(a hundred microfarad capacitor and a twenty mega Ohm resitor) which generate clock pulses to control a digital circuit. a)In the clock circuit,there is a resitor.Explain into details the purpose of the resistor b)What is the frequency of the clock circuit?
The oscillator circuit that does not generate phase shift is A.Hartley oscillator B.Harley Davidson oscillator C.Wien Bridge oscillator D.Phase Shift oscillator
b. Explain how to decide the sampling rate for a multi-frequency input signal. c. An ADC with word length of 24 bits. If the input analogue signal range is 3.7 V, what is the resolution of this ADC? d. Consider a thermocouple giving an output of 0.5 mVrc. What will be the word length required when its output passes through an ADC if temperatures from 0°C to 120°C are to be measured with resolution of 1.5°C?. Assume 12V as system voltage.
If the range of measurement is from -2 V to 2 V, what should the number of bits of the ADC be in order to provide a resolution of 0.125 V?
In a specific multiplexer, 4 select lines are present. Estimate the number of inputs present in the device.
The following figures show part of an analogue signal being digitised, at two different sampling rates. Make your explanation brief. (1) Explain how the difference in the sampling rates in figure 1 and figure 2 will affect the file sizes after digitisation. (ii) Which of the two sampling rates would you consider to be the least efficient to reproduce the original analogue signal accurately? (iii) What is the preferred digital sample rate (frequency) of an analogue audio signal that would be needed to accurately reproduce the original signal? Figure 1 Figure 2 15 14 13 12 11 10 6. 8 7 6 15 14 13 12 11 10 4 (iv) Draw the digital signals corresponding to the analogue signals is Figure 1 and Figure 2.
Describe the main features of the different types of technology that can be used for playing back recordings, including: Analogue and digital recording Dictating software Tape and disk recorders that are used for playing back recordings
can you pls show me the solution
1) Write 100µ Sec delay segments using •a) 100 kHz oscillator (Clock Frequency is 100KHz). •b) 4 MHz oscillator (Clock Frequency is 4 MHz). •c) 16 MHz oscillator (Clock Frequency is 16 MHz). •d) 32 MHz oscillator (Clock Frequency is 32 MHz). 2) Write 1mSec delay segment for 4 MHz oscillator. Show your calculations and your code