A MOTOR FITTED WITH A FLYWHEEL SUPPLIES A LOAD OF TORQUE 900 NM FOR 2 SECONDS. DURING NO-LOAD PERIOD THE FLYWHEEL REGAINS ITS ORIGINAL SPEED. THE MOTOR ORQUE IS REQUIRED TO BE LIMITED TO 450 NM. THE NO-LOAD SPEED OF THE MOTOR IS 500 R.P.M. AND ITS FULL- LOAD SLIP IS 10 PERCENT.

A MOTOR FITTED WITH A FLYWHEEL SUPPLIES A LOAD OF TORQUE 900 NM FOR 2 SECONDS. DURING NO-LOAD PERIOD THE FLYWHEEL REGAINS ITS ORIGINAL SPEED. THE MOTOR ORQUE IS REQUIRED TO BE LIMITED TO 450 NM. THE NO-LOAD SPEED OF THE MOTOR IS 500 R.P.M. AND ITS FULL- LOAD SLIP IS 10 PERCENT.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A four-pole induction motor drives a load at 2478 rpm. This is to be accomplished by using an electronic converter to convert a 400-V dc source into a set of three-phase ac voltages. Part A Find the frequency required for the ac voltages assuming that the slip is 4 percent. The load requires 2 hp. Express your answer to three significant figures and include the appropriate units. f= Submit Part B Value I = HA Request Answer Submit If the dc-to-ac converter has a power efficiency of 90 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the dc source. Express your answer to three significant figures and include the appropriate units. HÅ Value Units Request Answer ? Units ?
7. A 4-pole, d.c. shunt motor has a flux per pole of 0.04 Wb and the armature is lap-wound with 720 conductors. The shunt field resistance is 240 Ω and the armature resistance is 0.2 Ω. Brush contact drop is 1V per brush. Determine the speed of the machine when running (a) as a motor taking 60 A and (b) as a generator supplying 120 A. The terminal voltage in each case is 480 V.
It's a Physics question about mechanical engineering. A shunt motor has a speed of 900 rpm when it is connected to 120 V mains and delivering 12 hp. The total losses are 1048 W. Compute the power input, the line current, and the motor torque
An increase in the torque angle a results in: O A. No change in the induced torque O B. Decreasing the induced torque O C. Decreasing the load on the synchronous motor D. None of the other choices are correct O E. Increasing the induced totque
The field windings of a series motor has a resistance of 180 ohms at 30 degree Celsius. After running for 5 hours, the resistance increases to 140 ohms. If the temperature coefficient of the windings at o degree Celsius is o.o04. Find the new temperature of the windings. 0.004. 61.1111 DEGREE CELCIUS 63.3333 DEGREE CELCIUS 35.5322 DEGREE CELCIUS O 115.0544 DEGREE CELCIUS
A 240 V series motor takes 40 amperes when giving its rated output at 1500r.p.m. Its resistance is 0.3 ohm. Find what resistance must be added to obtain rated torque at 1000 r.p.m. 2 1.9 2.1 1.8
4-pole, d.c. shunt motor has a flux per pole of 0.04 Wb and the armature is lap-wound with 720 conductors. The shunt field resistance is 240 Ω and the armature resistance is 0.2 Ω. Brush contact drop is 1V per brush. Determine the speed of the machine when running (a) as a motor taking 60 A and (b) as a generator supplying 120 A. The terminal voltage in each case is 480 V. 5 3 K4 8 Derive the Torque equation of a D.C Motor.
A 400V, 25hp, 60HZ, 4 pole, Y-connected induction motor has the following impedances in ohms per phase referred to the stator circuit: R1=0.6410, X1=1.106 Q, Rp=11.080, Xf=6.680 .The total rotational (windage and friction) losses are 1100 W and are assumed to be constant. The core loss is jumped in with the rotational losses. For a rotor slip of 3.2% at the rated voltage and rated frequency, the stator current is
A 350 V shunt motor runs at it's normal speed of 720 r/min when the armature current is 90 A. The resistance of the armature is 0.3 ohm. Determine the following: (1) The kΦ1 of the motor. If armature current is 45 A and a resistance of 0.4 ohm is connected in series with the armature and the shunt field remaining constant determine the following: (2) The new kΦ2 of the motor. (3) The new speed of the motor in r/min If the current is 45 A and the shunt field is reduced to 75% of it's normal value by increasing resistance in the field circuit, determine the following: (4) The new kΦ2 of the motor. (5) The new speed of the motor in r/min
The following questions refer to a 6-pole DC generator has a simplex lap-wound armature containing 288 coils of 10 turns each. The resistance of each turn is 0.01 Ω. The flux per pole is 0.006 Wb. a.How many parallel paths does the armature of the generator have? b.How many turns does each path have? c.What is the resistance of each path in ohms? d.What is the speed of the generator's prime mover in RPM if it is generating an output voltage of 230.4 V? please help me answer this correctly with solution so that I can study it. Thank you!
A series motor has an armature resistance of 0.2 ohms and a series field resistance of 0.3 ohms. It is connected to a 240V supply at a particular load runs at 24 rev/s when drawing a 15A from the supply. Calculate the speed of the motor when the load is changed such that the current is increased to 30A. Answer is in rev/sec.