A motor car shaft consists of a steel tube 30 mm internal diameter and 4 mm thick. The engine develops 10 kW at 2000 r.p.m. Find the maximum shear stress in the tube when the power is transmit- ted through a 4 : 1 gearing.

A motor car shaft consists of a steel tube 30 mm internal diameter and 4 mm thick. The engine develops 10 kW at 2000 r.p.m. Find the maximum shear stress in the tube when the power is transmit- ted through a 4 : 1 gearing.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A alm T 1.20 m T B 1.20 m C 3 T The 60 mm diameter shaft is made of 6061-T6 aluminum having an allowable shear stress of Tallow 80 MPa. Find the corresponding angle of twist of disk A relative to disk C. Note: You will need to calculate the maximum allowable torque T first. Provide your answer for angle of twist in radians with 3 significant figures after the decimal point.
A shaft is required to fail when the torque on the shaft is 182 N-m. Find the suitable diameter of the shaft if the maximum shear stress is 50 .
The solid steel shaft is supported by the frictionless customer on D and E. This system The mile provided 5 kW of power in w dev / second and was connected to a motor at C. wwww ww www ww ww www wwwm www w A and B If gears get primary 2 kW and 3 kW, determine the minimum shaft diameter. w rotation speed and The safety shear stress is known and is included in the table below. pictures. wwww ww wwwwwwwww www wwwwww wwwwwwww wwwwwwwww w(cycle/second) = 100 tem(Mpa) = 40 3 kW 5 kW 2 kW A D B E C _
A flat key is to be designed for 100 mm diameter shaft which will transmit 200kw at 300 rpm . If the allowable shearing stress is 300 Mpa and key width is 10 mm ,determine the length of key.
A motor driving a solid circular steel shaftwith diameter d = 1.5 in. transmits 50 hp to a gear atB. The allowable shear stress in the steel is 6000 psi.Calculate the required speed of rotation (number ofrevolutions per minute) so that the shear stress in theshaft does not exceed the allowable limit.
Q.1 A rotary shaft carries distributed load of 250 w/m with a long 3m. The shaft transmits 35 KW at 290 rpm. A shaft is simply supported shaft. The mux. shear stresses 56 MPa and the allowable Compression stress 45 MPa, the safety factor is 1.5. Find the size of the shaft if it subjected to suddenly applied load.
The motor shown supplies 126 hp at 1340 rpm at A. Shafts (1) and (2) are each solid 1.86-in.-diameter steel [G=11400 ksi] shafts with lengths of L₁ = 79 in. and L₂ = 105 in., respectively. Assume Ng-27 teeth and N-42 teeth. The bearings shown permit free rotation of the shafts. (a) Determine the maximum shear stresses T₁, T2 produced in shafts (1) and (2). (b) Determine the rotation angle DA of gear D with respect to flange A. Answers: (a) T₁ = (b) P DIA Nc WWAMACOM Save for Later C 9.3808 = i 2.1378 e Textbook and Media NB L₁ B D TD ksi, 1₂: = i 14.5924 ksi. Attempts: 1 of 5 used Submit Answer
Member ABCD is a hollow circular steel shaft with a 4 inch outer diameter and a 3 inch inner diameter. It is rigidly attached to the wall at A. Externaly applied torques are TB of 1338 lb-ft, Tc of 1117 lb-ft, and TD of 884 lb-ft. Firstly obtain the internal torque generated, then calculate and input the maximum shear stress in section BC of the shaft: (f v max) = ___________ lb/in.2. Pay attention to unit conversion and calculate your answer to 1 decimal place.
Question 4. The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at A, and a torque of T 50 kN.m is applied to it at C, determine the angle of twist that occurs at C and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gst 115 GPa, Gbr 56 GPa. 3 m %3D 2 m 100 mm 50 mm T= 50 kN. m
A drilling riser is used to drill a 4km deep hole into the seabed. The riser can be approximated as a hollow steel shaft of 185mm and 160mm outer and inner diameter respectively. If the power exerted is 230kW and the speed of rotation of the drill is 75RPM, calculate the maximum shear stress in the shaft and the twist of one end relative to the other in degrees.(Note the angle of twist of a 4km drill string is going to be >> 360o ) G = 89 kN/mm2
Consider the case of shafts subjected to combined twisting moment and bending moment. A solid circular shaft is subjected to a bending moment of 2800 Nm and a torque of 10,000 Nm. The shaft is made of 45 C 8 steel having ultimate tensile stress of 700 MPa and ultimate shear stress of 500 MPa. Assuming a factor of safety as 5, determine, the diameter of the solid circular shaft. if a hollow circular shaft is to be used in place of the solid shaft, find the inside and outside diameter when the ratio of inside to outside diameter is 0.5.
A circular-closed-tube shaft, with an outer radius of 20 mm and an inner radius of 15 mm, and 650 mm long, is transmitting 50kW of power while rotating at a frequency of 20HZ. Compute the maximum shear stress (in Pa) and the angle of twist (in degree) for the shaft. The shear modulus G is 100 GPa. Hint: Please refer to the table of K and Q factors in the lecture notes.